System Components
Show/hide table
| |
| Illustration 1 | g06060993 |
|
A-Stop transmitter (1) A-Stop Button (2) Stop LED Indicator (3) Reset Indicator (4) Clear Button (5) A-Stop Reset Button (6) Test Button (7) Test/Power Indicator (8) Alarm Silence (9) Low Battery Indicator (10) Battery Charge Indicator (11) Charging Port | |
Show/hide table
| Callout | Button | Description |
|---|---|---|
| 1 | A-Stop Button | Used to transmit an A-Stop signal received by any Command machines equipped with the A-Stop system within range. The A-Stop signal will continue to transmit until the A-Stop Reset (5) is pressed.(1) |
| 2 | Stop LED Indicator | Blinks when A-Stop command is actively being transmitted. |
| 3 | Reset Indicator | Blinks after an A-Stop Clear message is transmitted. |
| 4 | Clear Button | Used to signal to any Command machines in the area to exit the A-Stop mode. Each transmitter that has signaled an A-stop must be pressed before the affected machine can resume operation.(2) |
| 5 | A-Stop Reset Button | Used to stop transmitting the A-Stop signal. The A-Stop Reset button (5) will only stop the transmission of the A-Stop signal, this button will not clear an affected machine to resume operation. |
| 6 | Test Button | Used to initiate an A-Stop system test(3) between the transmitter and all Command machines in range of the transmitter. The test button (6) is a momentary button. |
| 7 | Test/Power Indicator | Blinks periodically under normal operation. |
| 8 | Alarm Silence | Used to silence the audible alarm during an A-Stop event. |
| 9 | Low Battery Indicator | Used to show a low battery charge. |
| 10 | Battery Charge Indicators | Used to show the charging status of the transmitter battery. |
| 11 | Charging Port | Used to charge the transmitter.(4) |
Show/hide table
| (1) | Only the transmitter that sent the A-Stop signal can clear the A-Stop command. |
| (2) | Pressing the Clear button (4) does not allow the autonomous machine to resume the task the autonomous machine was assigned before the A-Stop was initiated. The Clear button (4) must be pressed and the user lock removed in the office before the autonomous machine will resume its original assignment it had before the A-Stop was activated. |
| (3) | For Test Station testing when used with the Stop button. |
| (4) | Use only the supplied charger 373-8621 Battery Charger to charge the transmitters. |
The transmitter has various modes of operation. Refer to Table 2 for more information.
Show/hide table
| Transmitter Modes | |
|---|---|
| Mode | Activation of Mode |
| A-Stop | Press and hold the A-Stop button for one second to activate. The stop indicator will start blinking while the A-Stop is active. |
| A-Stop Reset | Press and hold A-Stop Reset button for more than one second but less than six seconds. The test/power will resume blinking. The stop indicator will stop blinking. |
| Test | Press and hold Test button for two or more seconds. |
| Clear | Press and hold the Clear button for two or more seconds. The reset indicator will blink five times and the transmitter will beep five times. |
| Deep Sleep | Press and hold the A-Stop Reset button for more than six seconds. The reset, stop, and test/power indicators will blink once when entering sleep mode. The test/power indicator will not blink when in deep sleep mode. The transmitter will enter deep sleep after 24 hours of inactivity. |
Show/hide table
| |
| Illustration 2 | g03403452 |
|
Battery charge indicators | |
Show/hide table
| Charge Indicator LEDs | |||
|---|---|---|---|
| Ready LED (Green) | Charging LED (Yellow) | Fault LED (Red) | Indicated Condition Description |
| X | LED illuminates briefly after transmitter is attached to charger. LED will stay illuminated after charging is complete. | ||
| X | X | LEDs illuminate when the transmitter is being charged.(1) | |
| X | X | LEDs will illuminate when the transmitter is ready for charging but the temperature of the transmitter is out of range(2). In a suitable environment, charging will begin after the transmitter reaches a temperature in the allowable range. | |
| X | LED will illuminate when a latched fault condition is present. This condition can be the result of a bad battery, circuit failure, chip over temperature.(3) | ||
Show/hide table
| (1) | The charging will begin at a high rate charge followed by a top off charge. |
| (2) | Transmitter will only be charged if the temperature is between |
| (3) | If this condition is present, unplug the transmitter from the power supply and retry before troubleshooting further. |
Note: If none of the LEDs illuminate after the transmitter is connected to the charger, remove the transmitter from service.
Caterpillar Information System:
Autonomous Stop (A-Stop) General Information
Autonomous Stop (A-Stop) System A-Stop Transmitter
966M and 972M Wheel Loaders Power Train, Steering, Braking, Hydraulic & Machine Systems Coupler Cylinder - Quick Coupler
814K Wheel Dozer Machine Systems Cylinder Mounting - Steering
988K XE Wheel Loader Systems Electronic Control Module
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Control Valve
MH3037 Material Handler Camera
Front Strut Sealing System in Front Suspension Group May Fail on 795 AC, 797, 797B, 797F, and 797F XQ Off-Highway Trucks {0756, 7200, 7201} Front Strut Sealing System in Front Suspension Group May Fail on 795 AC, 797, 797B, 797F, and 797F XQ Off-Highway Trucks {0756, 7200, 7201}
AP500F Asphalt Paver Machine Systems Hydraulic Cylinder (Tow Point) - Remove and Install
AP500F Asphalt Paver Machine Systems Tow Arm - Remove and Install
2570D, 2670D Wheel Feller Buncher Safety Messages - WFB-Type Tractor
CCS7 Combination Compactor Lubricant Viscosities - Fluids Recommendations
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Joystick Control
Autonomous Stop (A-Stop) System A-Stop Transmitter Battery
Autonomous Stop (A-Stop) System Autonomous Stop Receivers
Autonomous Stop (A-Stop) System Antennas
Autonomous Stop (A-Stop) System General Information
Autonomous Stop (A-Stop) System Service Tools
Autonomous Stop (A-Stop) System Diagnostic Capabilities
Autonomous Stop (A-Stop) System A-Stop Fails to Clear
815K Soil Compactor and 816K Landfill Compactor Systems Push Arm - Left Hand
814K Wheel Dozer Machine Systems Cutting Edge
773G, 775G, and 777G Off-Highway Truck Automatic Lubrication System (Type B2) Control Module - Replace
Autonomous Stop (A-Stop) System A-Stop Fails to Register with the Test Station