| |
| Illustration 1 | g03005978 |
| |
| Illustration 2 | g03005979 |
There are several specific safety messages on this machine. The exact location of the hazards and the description of the hazards are reviewed in this section. Become familiarized with all safety messages.
Make sure that all of the safety messages are legible. Clean the safety messages or replace the safety messages if you cannot read the words. Replace the illustrations if the illustrations are not visible. When you clean the safety messages, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety message. Loose adhesive will allow the safety message to fall.
Replace any safety message that is damaged or missing. If a safety message is attached to a part of the machine that is replaced, install a safety message on the replacement part. Any Cat dealer can provide new safety messages.
Safety Message (1) is located in the cab on the front console of the machine.
| |
| Illustration 3 | g01055734 |
 |
|
Do not operate or work on this equipment unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Cat dealer for replacement manuals. Proper care is your responsibility. |
Safety Message (2) is located on the inside of the radiator access cover.
| |
| Illustration 4 | g01053324 |
|
|
Pressurized system! Hot coolant can cause serious burns, injury or death. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure. Read and understand the Operation and Maintenance Manual before performing any cooling system maintenance. |
Safety Message (3) is located on the front console of the machine.
| |
| Illustration 5 | g01370908 |
|
|
A seat belt should be worn at all times during machine operation to prevent serious injury or death in the event of an accident or machine overturn. Failure to wear a seat belt during machine operation may result in serious injury or death. |
This safety message (4) is located inside the cab on the right side next to the fuse panel.
| |
| Illustration 6 | g01506733 |
 |
|
Electrocution Hazard! Keep the machine and attachments a safe distance from electrical power. Stay clear 3 m (10 ft) plus twice the line insulator length. Read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions and warnings will cause serious injury or death |
Accumulator Under High Pressure(5)
Safety message (5) is located on the accumulator.
| |
| Illustration 7 | g01223282 |
|
|
Hydraulic accumulator contains gas and oil under high pressure. Improper removal or repair procedures could cause severe injury. To remove or repair, instructions in the service manual must be followed. Special equipment is required for testing and charging. |
Improper Connections for Jump Start Cables (6)
Safety Message (6) is located on the inside of the battery compartment cover.
| |
| Illustration 8 | g01370909 |
|
|
Explosion Hazard! Improper jumper cable connections can cause an explosion resulting in serious injury or death. Batteries may be located in separate compartments. Refer to the Operation and Maintenance Manual for the correct jump starting procedure. |
Refer to Operation and Maintenance Manual, "Engine Staring with Jump Start Cables".
Safety Message (7) is located in the cab on the front console.
| |
| Illustration 9 | g01370917 |
|
|
This machine is equipped with a Caterpillar Product Link communication device which should be deactivated in or near a blast site in compliance with applicable legal requirements. Failure to do so could cause interference with blasting operations resulting in serious injury or death. |
Refer to Special Instruction, REHS1642, "Operation of the Product Link System" for additional information.
Do Not Weld On The ROPS/FOPS (8)
Safety message (8) is located on the inside headliner of the cab.
| |
| Illustration 10 | g02944777 |
|
|
Structural damage, an overturn, modification, alteration, or improper repair can impair the structural protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a Cat dealer to determine the structural limitations without voiding required safety certification. |
This machine has been certified to the standards that are listed on the certification plate.
This safety message (9) is located inside the fuel fill access door.
| |
| Illustration 11 | g01115087 |
|
|
Do not tilt the cab when occupied. Before tilting the cab remove all loose articles from the cab, secure all windows and emergency exits, and then close the cab and cab riser doors. Failure to do so can result in personal injury or damage to the machine. |
Refer to Operation and Maintenance Manual, "Cab Tilting" for further information.
This safety message (10) is located on the air cleaner cover, inside the left-hand engine compartment.
| |
| Illustration 12 | g01067463 |
|
|
Do not use aerosol types of starting aids such as ether. Such use could result in an explosion and personal injury. |
Refer to Operation and Maintenance Manual, "Engine Starting" for further information.
This safety message (10) is located on both sides of the front frame near the articulation lock.
| |
| Illustration 13 | g01371644 |
|
|
Watch for falling trees when the machine is in operation. Personal injury or death can occur from being struck by falling trees. Keep all personnel |
This safety message (12) is located inside the cab on the front console.
| |
| Illustration 14 | g01506693 |
|
|
Do not operate the saw near other personnel. Serious injury or death can occur by contacting the moving blade or from flying objects. Read and understand the instructions and warnings in the Operation and Maintenance Manual. |
This safety message (13) is located on the lower left-hand rear frame near the right-hand door.
| |
| Illustration 15 | g01506755 |
|
|
Flying Debris Hazard! Do not position saw with discharge directed towards cab. Flying objects from the rotating saw will cause serious injury and/or death. Read and follow the instructions in the Operation and Maintenance Manual. |
This safety message (14) is located on the front console of the machine.
| |
| Illustration 16 | g01505753 |
|
|
Saw Blade Hazard. Do not operate the saw near other personnel. Serious injury or death can occur from contacting a moving saw blade. Read and follow the instructions in the Operation and Maintenance Manual. |
This safety message (15) is located on each side of the stick close to the attachment.
| |
| Illustration 17 | g01404266 |
|
|
Operation of the machine attachment can cause flying debris. The flying debris can cause serious injury or death. Stay clear of the machine and attachment while the attachment is in operation. |
This safety message (16 ) is located on the left-hand rear frame near the right-hand access door.
| |
| Illustration 18 | g02672426 |
|
|
Watch for falling trees when the harvester is in operation. Personal injury or death can occur from being struck by falling trees. Keep all personnel 300 feet from the harvester when the harvester is in operation |
This safety message (17 ) is located on the front frame near the articulation lock.
| |
| Illustration 19 | g01371647 |
|
|
Crushing Hazard. There is no clearance for a person in this area when the machine turns. Severe injury or death from crushing could occur. Connect the steering frame lock between front and rear frames before lifting, transporting, or servicing the machine in the articulation area. Disconnect the steering lock and secure before resuming operation. |
Reversing Fan (Severing Hand) (18)
Safety Message (18) is located on the left-hand hood and on the side door.
| |
| Illustration 20 | g01460652 |
|
|
Rotating fan blades can result in personal injury or death. Stop the engine and allow the fan to come to a complete stop before making any test or adjustment. Before starting the engine, make sure all of the finger guards are installed and the guard door is closed. Do not allow any tools or test equipment to protrude or vibrate into the path of the rotating fan blades. |
Rotating fan could cause serious injury or death. Turn off key to shut down machine. Read the Operator manual for further instruction.
Rotating serpentine belt and alternator fan could cause serious injury or death. Turn off key to shut down machine.
Crush Point (Severing Hand) (19)
Safety Message (19) is located on the outside left-hand goal post of the cab.
| |
| Illustration 21 | g01803414 |
|
|
There is no room for a person in this area when tilting or lowering the machine cab. Stay clear of area when tilting or lowering the cab. Severe personal injury or death from crushing could occur. |
Cab tilting could cause serious injury or death. Turn off key to shut down machine. Read the Operator manual for further instruction.
Before raising or lowering cab, verify that all personnel are clear of the area. Do not tilt cab unless you have read and understand the correct tilting procedure in the Operation and Maintenance Manual , "Cab Tilt Procedure".