Transmission - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | QTY |
A | 396-6461 | Bracket As | 1 |
439-3940 | Link Bracket | 1 | |
8S-9089 | Bolt | 1 | |
1D-4719 | Nut | 1 | |
B | 154-6182 | Forcing Bolts | 2 |
C | 422-2352 | Jack Stand Gp | 1 |
D | 2D-1201 | Eyebolts | 2 |
Start By:
- Remove draw bar
- Remove main drive shaft.
- Remove drive axles.
- Drain the transmission. Refer to Operation and Maintenance Manual, "Power Train Oil - Change" for the correct draining and filling procedure.
Show/hide table
Illustration 1 g02606744 - Remove yoke (1) and plate (2).
Show/hide table
Illustration 2 g03851393 - Remove cover (3).
Show/hide table
Illustration 3 g03851395 - Disconnect hose assembly (4) and harness assembly (5).
Show/hide table
Illustration 4 g03851396 - Remove cover (6).
Show/hide table
Illustration 5 g03851397 - Attach Tooling (A) to transmission and bevel gears (7).
Show/hide table
Illustration 6 g03851400 - Remove bolts (8). Do not remove bolts (9).
Show/hide table
Illustration 7 g03851401 - Use Tooling (B) in order to remove transmission and bevel gears (7).
Show/hide table
Illustration 8 g03851403 - Slide transmission and bevel gears (9) out until transmission and bevel gears (7) rests on the stops. Place transmission and bevel gears (7) onto Tooling (C).
Show/hide table
Illustration 9 g03851404 - Attach a suitable lifting device to Tooling (D). The weight of transmission and bevel gears (7) is approximately
847 kg (1867 lb) . Remove transmission and bevel gears (7).
- Install transmission and bevel gears (10) in the reverse order of removal.
- Tighten bolts (8) to a torque of
105 ± 20 N·m (77 ± 15b ft) .
- Tighten bolts (8) to a torque of
Caterpillar Information System:
2015/08/24 A New Spring for the Belt Tensioner Is Now Used In the Fan Drive Group on Certain 773E Off-Highway Trucks {1357, 1358, 1359, 1397}
MD6200 Rotary Drill Air Compressor Oil Separator Filter - Replace - High Pressure - If Equipped
Dealer Services Portal Provides No Feedback on Subscription Requests or Successes{7606} Dealer Services Portal Provides No Feedback on Subscription Requests or Successes{7606}
SE34 V and SE34 VT Asphalt Screeds Screed - Lubricate
CW16 Pneumatic Compactor Machine Systems Axle (Front) - Remove and Install
SE34 V and SE34 VT Asphalt Screeds Access Doors and Covers
2015/07/27 Improved Bracket Clearance with Fuel Tank Is Now Available For Certain 797FOff-Highway Trucks {7050, 7050}
415F2 Industrial Loader Towing the Machine
SE34 V and SE34 VT Asphalt Screeds Lifting and Tying Down the Machine
415F2 Industrial Loader Monitoring System
SE34 V and SE34 VT Asphalt Screeds Thickness Control Screw Adjustment
R1600G Underground Load Haul Dump Machine Repower With C11 Engine {1000, 7000} R1600G Underground Load Haul Dump Machine Repower With C11 Engine {1000, 7000}
415F2 Industrial Loader Rollover Protective Structure (ROPS) - Inspect
CP54B, CP56B, CP68B, CP74B, CS54B, CS56B, CS64B, CS66B, CS68B, CS74B, CS76B and CS78B Vibratory Soil Compactors Machine Electronic Control System Electrical Power Supply - Test
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Clean Emissions Module - Remove and Install
AP500F Asphalt Paver Propel System Pressure Limiter Valve - Test and Adjust - Right Propel
CW16 Pneumatic Compactor Machine Systems Wheel and Tire - Remove and Install
CW16 Pneumatic Compactor Machine Systems Water Tank - Remove and Install
CW16 Pneumatic Compactor Machine Systems Water Spray Pump - Remove and Install
CW16 Pneumatic Compactor Machine Systems Spray Bar - Remove and Install
CW16 Pneumatic Compactor Machine Systems Piston Pump (Propel) - Remove and Install
SE34 V and SE34 VT Asphalt Screeds Screed - Check/Adjust
CW16 Pneumatic Compactor Machine Systems Metering Pump (Steering) - Remove and Install
CW16 Pneumatic Compactor Machine Systems Hydraulic Tank - Remove and Install