Sliding Frame and Bearing - Install
- Install wear rings (8) and (11), piston seal (10), and lip seal (12) onto piston (9).
- Lubricate piston (9) and the seals with clean hydraulic oil. Install piston (9).
- Install O-ring seal (7) onto cap (5). Lubricate O-ring seal (7) and the bore with clean hydraulic oil. Install cap (5) and bolts (6).
- Install the remaining cylinder assemblies onto sliding frame (4).
Show/hide table
Illustration 3 g03327990 - Use a suitable lifting device to position sliding frame (2). The weight of sliding frame (2) is approximately
204 kg (450 lb) . - Install bolts (4) and bar (3). Repeat for the other side.
- Tighten bolts (1) and bolts (4) to a torque of
230 ± 20 N·m (170 ± 15 lb ft) plus turn an additional 30 degrees.
Show/hide table
Illustration 1 | g03327992 |
Show/hide table
Illustration 2 | g03327991 |
End By:
- Install the swing cylinder.
- Install the swing frame.
Caterpillar Information System:
2015/07/16 A New Turbine Inlet Manifold Support Bracket Is Used on C175 Off-Highway Truck Engines {1059}
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Machine Systems Sliding Frame and Bearing - Remove
Cat® Command For Hauling MID 039 - CID 0841 - FMI 03
Cat® Command For Hauling MID 039 - CID 0840 - FMI 03
Cat® Command For Hauling MID 039 - CID 0839 - FMI 03
16M Series 3 and 18M Series 3 Motor Grader Systems Fuel Tank
PL83 and PL87 Pipelayer Systems Brake Control Valve
16M Series 3 and 18M Series 3 Motor Grader Systems Sideshift Cylinder - Mounting
2015/07/08 A New Cat® Optimized Suspension Seat Is Now Available for Certain Machines {7312, 7324}
MWL/LWL Neutralizer Valve Leakage {4330} MWL/LWL Neutralizer Valve Leakage {4330}
16M Series 3 and 18M Series 3 Motor Grader Systems Centershift Cylinder and Mounting
16M Motor Grader Lubrication Pump Oil - Fill - Autolube
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Machine Systems Stabilizer Cylinder - Remove and Install
2015/05/12 New Troubleshooting Procedure Is Now Available for all Cat® Products Equipped with PL321 VIMS (PL321 VSR) {7606}
PL83 and PL87 Pipelayers Machine Systems Counterbalance Valve (Counterweight) - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Load Sheave Block (Lower) - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Gear Pump (Counterweight) - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Main Control Valve - Remove and Install
Check Final Drive O-Ring Seal on R2900G and R3000H LHD Machines{4050} Check Final Drive O-Ring Seal on R2900G and R3000H LHD Machines{4050}
793F and 793F XQ Off-Highway Truck Hydraulic Fan and Steering System Bypass Switch (Rear Axle Lubrication Filter)
14M3 Motor Grader Machine Systems Wheel Mounting
16M Series 3 and 18M Series 3 Motor Grader Systems Frame - Front
422F2, 427F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Hydraulic and Steering System Hydraulic Tank and Filter
422F2, 427F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Hydraulic and Steering System Bank Valve (Loader) - Single Tilt - Direct Operating