AP655F and AP655F L Asphalt Paver Machine Systems Caterpillar


Deflector

Usage:

AP655F 452


Illustration 1g06218343

Table 1
Item  Qty  Part  Specification Description 
129-3180 Locknut  Use the following procedure to tighten the locknut:
Tighten the locknut to 40 ± 10 N·m (30 ± 7 lb ft).
Then, back off locknuts by 180 degrees. 
170-8555 Bolt  Insert bolt into frame bar (block) so that the top of the bolt head is 64.0 ± 1.0 mm (2.52 ± 0.04 inch) from the bottom surface of the block.
Torque to 100 ± 20 N·m (74 ± 15 lb ft)
12  8T-4195 Bolt  Before assembly, apply Loctite 243 to threads.
Torque to 15 ± 2 N·m (133 ± 18 lb in)
8T-4196 Bolt  Before assembly, apply Loctite 243 to threads. 
479-6661 Setscrew  Before assembly, apply black Loctite 593 to threads. 


Illustration 2g06218344

Table 2
Item  Qty  Part  Specification Description 
176-5311 Locknut  Use adapter nut to set a gap of less than 0.10 mm (0.004 inch) between the deflector plate and tamper bar below each adjuster.
Torque to 28 ± 5 N·m (248 ± 44 lb in)
422-4637 Nut  Before assembly, apply Loctitte C5A Copper Anti-Seize to the threads. 


Illustration 3g06218510
Top view

Table 3
Item  Qty  Part  Specification Description 
176-5311 Locknut  Use adapter nut to set a gap of less than 0.10 mm (0.004 inch) between the deflector plate and tamper bar below each adjuster.
Torque to 20 ± 5 N·m (177 ± 44 lb in)

Caterpillar Information System:

C3.4B Engines Power Take-Off - Test
SE60 V Asphalt Screed Machine System Screed Plate
785G Off-Highway Truck Systems Relief Valve (Steering)
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Quick Coupler Pressure - Test and Adjust
785G Off-Highway Truck Systems Steering Linkage and Cylinder Mounting
Magnetic Switch Group Fails on Certain 773E, 770G, and 772G Off-Highway Trucks{1408, 7499} Magnetic Switch Group Fails on Certain 773E, 770G, and 772G Off-Highway Trucks{1408, 7499}
785G Off-Highway Truck Systems Steering Cylinder
785G Off-Highway Truck Systems Pump Drive Group
785G Off-Highway Truck Systems Liquid Level Sensor (Hydraulic Tank)
785G Off-Highway Truck Systems Front Wheel
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission Hydraulic Control Operation
PL83 and PL87 Pipelayers Refrigerant Dryer - Replace - If Equipped
C3.4B Engines Relay - Test - ECM Main Relay
785G Off-Highway Truck Systems Oil Filter (Brake Cooling)
785G Off-Highway Truck Systems Diverter Valve (Rear Brake Cooling)
794 AC Off-Highway Truck Machine Systems Tire and Rim (Front) - Remove and Install
C3.4B Engines Relay - Test - SCR Relay
2014/12/10 New Fuel Lines Are Used on Certain 24M Motor Grader Engines {1274}
320D2 Forest Machine Machine System Specifications Solenoid Valve and Mounting - Front Brake Cooling Diverter
745 Articulated Truck Cooling System Coolant (ELC) - Change
735C and 745C Articulated Trucks Cab Air Filter - Clean/Replace
785G Off-Highway Truck Systems Oil Filter (Brake System)
PL83 and PL87 Pipelayers Boom Line - Install
C7 and C9 Industrial Engines CAN Data Link - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.