Piston Pump (Vibratory) - Remove and Install
Start By:
- Remove the cab.
Show/hide table
 |
|
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
- Disconnect all hose assemblies (3) from the vibratory piston pump (1). Disconnect harness assembly (2).
Show/hide table
Illustration 2 g02711981 - Attach a suitable lifting device to vibratory piston pump (1). The weight of vibratory piston pump (1) is approximately
50 kg (110 lb) . Remove vibratory piston pump (10).
Show/hide table
| |
| Illustration 1 | g02883758 |
- Install vibratory piston pump (1) in the reverse order of removal.
Caterpillar Information System:
2012/03/21 A New Shimming Procedure is Now Used on the Truck Bodies on 793F Off-Highway Trucks {7000, 7006, 7250, 7258, 7960}
SC-57 Felling Head General Hazard Information
2011/09/28 A New Break-out Harness Is Used for the Fuel Control Module on C175 Off-Highway Truck Engines {1403, 1408}
2011/09/19 Improved O-ring Seals for the Fuel Injection Lines Are Used in Certain 3500 Off-Highway Truck Engines {1252, 7555}
CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B and CC34B Vibratory Utility Compactors Machine Electronic Control System General Information
2011/09/27 Updated Torque Values for Relief Valve Plugs on Certain Backhoe Loaders {5051}
120M Series 2 Motor Grader Engine Supplement Rear Chassis Support - Remove and Install
793F AC Off-Highway Truck Hydraulic Fan and Steering System Wheel and Brake
793F AC Off-Highway Truck Power Train Final Drive Lubrication Pressure - Test
2011/09/19 Operator Techniques Can Improve Shift Quality on Certain Motor Graders {1265, 1269, 1918, 3065, 3167, 3168, 5705, 7000, 7300}
Machine Electronic Control System Electrical Component and Connector Locations
CP34 and CS34 Vibratory Soil Compactors Diagnostic Capabilities
R1600H Load Haul Dump Drive Shaft Universal Joints, Splines and Bearings - Inspect/Lubricate
R1600H Load Haul Dump Ejector Cylinder Bearing - Lubricate - If Equipped
R1600H Load Haul Dump Ejector Plate Bearing - Lubricate - If Equipped
2011/12/21 New Axle Oil Cooling Fan Motor Harness Now Used on R1600 and R1600G Load Haul Dump Machines {1365, 1408}
Machine Electronic Control System Electronic Control Module (ECM) - Flash Program
CW34 Pneumatic Compactor Machine Electronic Control System Electronic Control Module (ECM) - Configure
CB44B, CB54B, CD44B and CD54B Vibratory Asphalt Compactors Machine Electronic Control System Electronic Control Module (ECM) - Replace
CW34 Pneumatic Compactor Machine Electronic Control System Service Tools
Machine Electronic Control System Using the Electronic Service Tool to Determine Diagnostic Codes
CP56B, CP68B, CP74B, CS56B, CS68B, CS74B and CS78B Vibratory Soil Compactors Machine Electronic Control System Using the Operator Monitor to Determine Diagnostic Codes
PL87 Pipelayer Transmission Scavenge Screen - Clean
950M, 962M, 950M Z and 962M Z Wheel Loaders Quick Coupler - Remove and Install