A New Oversized Cylinder Bore Liner Seal Insert Is Available for 3500 Engine Cylinder Block Salvage {1201, 7555}
- Caterpillar Products: Machine Engines
- All 3500 Series
The new 335-8971 Insert with a 0.254 mm (0.010 inch) oversized outer diameter is now available.
The new 335-8971 Insert has the same thickness as the 353-5618 Insert, but the new insert provides an oversized outer diameter.
The new 335-8971 Insert is intended for use as needed in replacing loose standard-sized inserts.
Show/hide table
Illustration 1 | g02649139 |
Dimensions for the insert (N) Outside diameter (P) Thickness of the insert (R) Wall thickness of the insert (S) Radius on insert |
Show/hide table
Dimensions for the Liner Seat Insert     | ||||
Part Number     | Outside Diameter (N) (4)     | Thickness of the Insert (P)     | Wall Thickness of the Insert (R)     | Radius (S)     |
353-5617 120-4334 (1) (2)     |
212.115 ± 0.013 mm (8.3510 ± 0.0005 inch)     |
5.080 ± 0.025 mm (0.2000 ± 0.0010 inch)     |
6.528 ± 0.032 mm (0.2570 ± 0.0013 inch)     |
0.90 ± 0.13 mm (0.035 ± 0.005 inch) by 30 degrees     |
353-5618 120-4337 (1) (2)     |
7.620 ± 0.025 mm (0.3000 ± 0.0010 inch) |
|||
335-8971 (3)     | 212.370 ± 0.013 mm (8.3610 ± 0.0005 inch)     |
6.655 ± 0.032 mm (0.2620 ± 0.0013 inch) |
Show/hide table
( 4 ) | Do not measure this dimension |
( 1 ) | Canceled |
( 2 ) | Non-chamfered insert |
( 3 ) | Oversize |
Caterpillar Information System:
PL83 and PL87 Pipelayers Machine Systems Cable - Remove and Install
PL83 and PL87 Pipelayers Machine Systems Refrigerant Accumulator - Remove and Install
2015/04/07 New VIMSpc Software Is Now Available On Certain Cat Product {0785, 7601}
422F, 428F, 432F, 434F and 444F Backhoe Loaders Hydraulic Oil Sample - Obtain
773G and 775G Off-Highway Trucks Specifications
428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Fuel System Water Separator - Drain
PL87 Pipelayer Machine Systems Drawbar - Remove and Install
Procedure to Install a New Solenoid for the Autolube System on Certain 16M and 24M Motor Graders{7516, 7540} Procedure to Install a New Solenoid for the Autolube System on Certain 16M and 24M Motor Graders{7516, 7540}
2012/02/06 The Buffers for the Exhaust Temperature Sensors Are Relocated on C175 Engines in 793F, 795F, and 797F Off-Highway Trucks {1408}
Installing the New 368-4968 Engine Support Gp to Increase the Durability of the Front Housing on Certain PM-200 Cold Planers{1152, 1153, 1154} Installing the New 368-4968 Engine Support Gp to Increase the Durability of the Front Housing on Certain PM-200 Cold Planers{1152, 1153, 1154}
428F, 432F, 434F and 444F Backhoe Loaders Additional Messages
C7.1 Engines For Caterpillar Built Machines NRS Exhaust Gas Temperature Is High
PL83 and PL87 Pipelayers Machine Systems Boom - Remove and Install
PL87 Pipelayer Machine Systems Cooler Bypass Valve - Remove and Install
C9.3 Engines for Caterpillar Built Machines Mounting Straps
C9.3 Engines for Caterpillar Built Machines Mounting Straps
PL83 and PL87 Pipelayers Machine Systems Boom Sheave Block (Lower) - Disassemble
2011/09/12 An Improved Fan Shroud Assembly Is Now Used on Certain Off-Highway Trucks {1356}
773G and 775G Off-Highway Truck Suction Screen (Transmission Scavenge) - Clean
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Crankcase Guard (Front) - Remove and Install
R1600G Load Haul Dump 3176C Engine Supplement Radiator Cap
C9.3 Tier 4 Final Engines Camshaft
C9.3 Engines for Caterpillar Built Machines Camshaft
C7.1 Engines For Caterpillar Built Machines Power Is Intermittently Low or Power Cutout Is Intermittent