Steering Control Valve - Disassemble
Start By:
- Remove the Steering Valve.
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1U-7600 | Slide Hammer Puller Gp | 1 |
| 8T-7585 | Screw | 1 | |
- Remove all fittings (1). Remove manifold (2). Remove elbow (3).
Show/hide table
Illustration 2 g02224254 - Remove O-ring seal (4) from elbow (3).
Show/hide table
Illustration 3 g02224274 - Remove O-ring seals (5) from manifold (2).
Show/hide table
Illustration 4 g02224294 Show/hide table
Personal injury can result from being struck by parts propelled by a released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to release the spring force.
- Remove bolts (6) and spring housing (7).
Show/hide table
Illustration 5 g02224354 - Remove bolts (8) and sensor assembly (9).
Show/hide table
Illustration 6 g02224393 - Remove O-ring seal (10) from sensor assembly (9).
Show/hide table
Illustration 7 g02224414 - Remove stem valve (11).
Show/hide table
Illustration 8 g02224579 Show/hide tablePersonal injury can result from being struck by parts propelled by a released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to release the spring force.
- Remove flange bolt (12) and retainer (13) from stem valve (11). Remove spring (14) and retainer (15) from stem valve (11). Remove probe assembly (16) from stem valve (11).
Show/hide table
Illustration 9 g02224635 - Remove O-ring seal (17).
Show/hide table
Illustration 10 g02224657 - Remove sensor housing (18).
Show/hide table
Illustration 11 g02224673 - Remove O-ring seal (19).
Show/hide table
Illustration 12 g02224675 - Remove relief valves (20).
Show/hide table
Illustration 13 g02224714 - Remove O-ring seal (21), backup ring (22), and O-ring seal (23) from relief (20). Repeat for the other two relief valves.
Show/hide table
Illustration 14 g02224773 - Remove retaining ring (24). Use Tooling (A) to remove check valve (25).
Show/hide table
Illustration 15 g02224813 - Remove backup ring (26) and O-ring seal (27) from check valve (25).
Show/hide table
Illustration 16 g02224894 - Remove nut (28), and coil assembly (29). Repeat for the three other solenoid valves. Remove nut (31) and coil assembly (30).
Show/hide table
Illustration 17 g02225113 - Remove all four cartridge assemblies (32). Remove cartridge assembly (33).
Show/hide table
Illustration 18 g02225194 - Remove O-ring seal (34) and O-ring seal (35) from cartridge assembly (32). Repeat for the remaining three cartridge valves.
Show/hide table
Illustration 19 g02225816 - Remove backup rings (36) and O-ring seal (39) from cartridge valve (33). Remove backup rings (37) and remove O-ring seals (40) and (38) from cartridge valve (33).
Show/hide table
Illustration 20 g02225873 - Remove bolts (41) and remove solenoid manifold (42).
Show/hide table
Illustration 21 g02225894 - Remove O-ring seals (43) from valve body (44).
Show/hide table
| |
| Illustration 1 | g02224196 |
Caterpillar Information System:
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Symptom Troubleshooting
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Emerging Symptom Information
R1600G Load Haul Dump 3176C Engine Supplement Engine, Torque Converter and Updrive Gears - Install
C9.3 Tier 4 Final Engines Belt Tensioner - Alternator and Compressor
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
Excessive Wear of the Crankshaft Rear Thrust Washer in Large Off-Highway Trucks{1202} Excessive Wear of the Crankshaft Rear Thrust Washer in Large Off-Highway Trucks{1202}
C9.3 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C9.3 Engines for Caterpillar Built Machines Compression Brake - Remove and Install
142-1664 Adjustable Lifting Bracket Group{0599, 0629, 0700, 0729, 0757, 1122} 142-1664 Adjustable Lifting Bracket Group{0599, 0629, 0700, 0729, 0757, 1122}
C9.3 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C9.3 Engines for Caterpillar Built Machines Cylinder Block Cover - Remove and Install
2011/05/26 An Improved Relief Valve Group is Now Used in the Torque Converter Filter and Lines Group on the 777F Off-Highway Trucks {3103}
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Steering Control Valve - Assemble
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Wiring Harness (Open Circuit) - Test
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Wiring Harness (Short Circuit) - Test
3516B Engine for 994F and 994H Wheel Loaders Electrical Power Supply - Test
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Electrohydraulic Control (Joystick) - Remove and Install
2011/05/25 Updated Cat EPD Alternator Failure Report Template Is Now Available for Cat Generator Sets {1404}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Cat Data Link
Cat® Detect Object Detection Camera - Clean
Cat® Detect Object Detection Configuration Screen
Cat® Detect Object Detection Diagnostic Summary Screen
Cat® Detect Object Detection Display - Clean
Cat® Detect Object Detection Display Navigation