Final Drive Planetary - Install
安装步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 项目 | 零件号 | 零件描述 | 数量 |
| A | 6V-4876 | 润滑剂 | 1 |
- 将适当的起吊设备连接到支架 (4) 上。 支承 (4) 的重量约为 114 kg (251 lb)。 将支架 (4) 和螺栓 (16) 安装到终传动行星齿轮 (18) 。 将螺栓 (16) 拧紧至 400 ± 50 N·m (295 ± 37 lb ft) 的扭矩。
Show/hide table
 | |
| 图 1 | g02580837 |
- 将工具 (A) 涂覆到活塞马达 (15) 的花键上。 将活塞马达 (15) 和螺栓 (17) 安装到终传动行星齿轮 (18) 。
- 将软管组件 (6) 、 (9) 、 (10) 和 (11) 连接到活塞马达和终传动组件 (4) 。
Show/hide table
 | |
| 图 2 | g02580531 |
- 连接适当的起吊设备或将适当的起吊设备放置在终传动组件 (4) 的下方。 终传动组件 (4) 的重量约为 406 kg (894 lb)。 将终传动组件 (4) 和螺栓 (14) 安装到机器。
- 将软管组件 (10) 和 (11) 连接到活塞泵上。
Show/hide table
 | |
| 图 3 | g02580341 |
- 连接软管组件 (9) 。
- 连接三个软管组件 (6) 。
- 安装卡箍 (13) 、板、夹子和螺栓。
- 安装卡箍 (12) 、板和螺栓。
- 安装卡箍 (7) 、软管组件 (6) 、线束组件 (8) 、板和螺栓。
Show/hide table
 | |
| 图 4 | g02580187 |
- 将固定线束组件 (8) 的电缆扎带安装到机器。
- 连接线束组件 (5) 。
Show/hide table
 | |
| 图 5 | g02580186 |
- 将固定线束组件 (5) 的电缆扎带安装到终传动 (4) 。
- 安装盖 (2) 、垫圈和螺栓 (3) 。
Show/hide table
 | |
| 图 6 | g02580185 |
- 安装挡泥板 (1) 、螺栓、垫圈和螺母。
Show/hide table
 | |
| 图 7 | g02580182 |
- 将固定线束组件的电缆扎带安装到挡泥板 (1) 。
End By: 安装后轮。 请参考 拆解和装配, "后轮 - 拆卸和安装" 。
Caterpillar Information System:
AP1000F Asphalt Paver Machine Systems Final Drive Planetary - Remove
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor (Propel) - Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor (Propel) - Remove
3516B Engine for 994F and 994H Wheel Loaders Configuration Parameters
777G Off-Highway Truck Lubrication Pump Oil - Change
Comfort Series Seat For Caterpillar Machines Optimized Seat with Lumbar, Side Controls, and Slide Swivel
777G Off-Highway Truck Lubrication Pump Oil Level - Check
2011/05/26 New Cylinder Pack Assemblies Are Available in Sets for Certain Machines Equipped with C18 Engines {1201, 1216, 1225, 1239}
C13, C15, and C18 Tier 4 Final Engines Exhaust Gas Valve (NRS)
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280} NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
PL83 Pipelayer Reference Material
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Auxiliary) - Install
2011/07/20 An Updated Procedure for the Inspection, Repair, and Component Replacement on the Frames of Certain Off-Highway Trucks is Available {7000, 7051}
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
Front Axle Steering Cylinder Hose Guard for Certain M Series Motor Graders{7164} Front Axle Steering Cylinder Hose Guard for Certain M Series Motor Graders{7164}
E SeriesBackhoe Loader Stabilizer Cylinder Drift{5468} E SeriesBackhoe Loader Stabilizer Cylinder Drift{5468}
541 Series 2 and 552 Series 2 Track Feller Bunchers Condenser (Refrigerant) - Clean
521B and 522B Track Feller Bunchers Monitoring System - System Setup and Change
793F Off-Highway Truck Damper (Crankshaft) - Inspect
C9.3 Tier 4 Final Engines Electronic Unit Injector Wiring
C175-16 and C175-20 Generator Set Engines Fuel Injector
C4.4 Engines For Caterpillar Built Machines CID 0001 FMI 05