Final Drive Planetary - Remove
拆卸步骤
开始:
- 拆下后轮。 请参考拆解和装配, "后轮 - 拆卸和安装" 。
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修机器时,务必小心,确保用容器盛接流出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关可提供予卡特彼勒机器的工具及适合于盛装油液的容器,请参阅专门出版物, NENG2500, "卡特彼勒工具及车间用品指南"。 根据当地法规处置所有液体。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。
- 拆下将线束组件固定到挡泥板 (1) 的电缆扎带。
Show/hide table
图 1 | g02580182 |
- 拆下螺栓、螺母、垫圈和挡泥板 (1) 。
- 拆下螺栓 (3) 、垫圈和盖 (2) 。
Show/hide table
图 2 | g02580185 |
- 拆下将线束组件 (5) 固定到终传动 (4) 的电缆扎带。
Show/hide table
图 3 | g02580186 |
- 断开线束组件 (5) 。
- 拆下螺栓、板和卡箍 (7) 。
Show/hide table
图 4 | g02580187 |
- 拆下将线束组件 (8) 固定到机器的电缆扎带。 将线束组件 (8) 固定到一边,以接近软管组件 (6) 。
- 拆下螺栓、板和卡箍 (12) 。
Show/hide table
图 5 | g02580341 |
- 拆下螺栓、夹子、板和卡箍 (13) 。
- 断开三个软管组件 (6) 。
- 断开软管组件 (9) 。
- 将软管组件 (10) 和 (11) 从活塞泵上断开。
- 连接适当的起吊设备或将适当的起吊设备放置在终传动组件 (4) 的下方。 拆下螺栓 (14) ,然后将终传动组件 (4) 从机器上拆下。 将软管组件 (6) 、 (9) 、 (10) 和 (11) 作为一个装置从终传动组件 (4) 上拆下。 终传动组件 (4) 的重量约为 406 kg (894 lb)。
Show/hide table
图 6 | g02580531 |
- 将软管组件 (6) 、 (9) 、 (10) 和 (11) 从活塞马达和终传动组件 (4) 上断开。
- 将适当的起吊设备连接到支架 (4) 上。 支承 (4) 的重量约为 114 kg (251 lb)。 将螺栓 (16) 和支架 (4) 从终传动行星齿轮 (18) 上拆下。
Show/hide table
图 7 | g02580837 |
- 将螺栓 (17) 和活塞马达 (15) 从终传动行星齿轮 (18) 上拆下。
Caterpillar Information System:
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor (Propel) - Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Motor (Propel) - Remove
3516B Engine for 994F and 994H Wheel Loaders Configuration Parameters
777G Off-Highway Truck Lubrication Pump Oil - Change
Comfort Series Seat For Caterpillar Machines Optimized Seat with Lumbar, Side Controls, and Slide Swivel
777G Off-Highway Truck Lubrication Pump Oil Level - Check
2011/05/26 New Cylinder Pack Assemblies Are Available in Sets for Certain Machines Equipped with C18 Engines {1201, 1216, 1225, 1239}
C13, C15, and C18 Tier 4 Final Engines Exhaust Gas Valve (NRS)
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280} NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
PL83 Pipelayer Reference Material
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Auxiliary) - Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Auxiliary) - Remove
AP1000F Asphalt Paver Machine Systems Final Drive Planetary - Install
2011/07/20 An Updated Procedure for the Inspection, Repair, and Component Replacement on the Frames of Certain Off-Highway Trucks is Available {7000, 7051}
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
Front Axle Steering Cylinder Hose Guard for Certain M Series Motor Graders{7164} Front Axle Steering Cylinder Hose Guard for Certain M Series Motor Graders{7164}
E SeriesBackhoe Loader Stabilizer Cylinder Drift{5468} E SeriesBackhoe Loader Stabilizer Cylinder Drift{5468}
541 Series 2 and 552 Series 2 Track Feller Bunchers Condenser (Refrigerant) - Clean
521B and 522B Track Feller Bunchers Monitoring System - System Setup and Change
793F Off-Highway Truck Damper (Crankshaft) - Inspect
C9.3 Tier 4 Final Engines Electronic Unit Injector Wiring
C175-16 and C175-20 Generator Set Engines Fuel Injector