Steering System - Purge
Reference: Before you perform this procedure, refer to Testing and Adjusting, "Machine Preparation".
The following will explain the procedure for purging the steering system.
Show/hide table
Tool | Part Number | Description | Qty |
D | 8T-2362 | Adapter(1) | 4 |
7J-0204 | O-Ring Seal | 4 | |
6V-8628 | Elbow | 4 | |
3J-7354 | O-Ring Seal | 4 | |
4J-5477 | O-Ring Seal | 4 | |
9C-2394 | Hose As | 2 | |
F | 6V-3668 | Bolt | 2 |
5P-8245 | Hard Washer | 8 |
Show/hide table
(1) | The adapter must be change 02. Exterior thread is 3/8 by 24. Interior threads are 7/16 by 20. |
- Move the machine to a smooth horizontal location.
- Chock the wheels.
- Lower all of the implements.
Show/hide table
Illustration 1 g03863275 View of front axle - Install bolt and washer (F) into the location shown in Illustration 1.
Show/hide table
Illustration 2 g01459676 Typical top view of front axle
(1) Steering cylinders
(2) Plugs - Remove plugs (2) from each steering cylinder (1).
- Use the parts that are listed in Table 1 in order to connect the port of the rod end to the port of the head end. Perform this procedure for both of the cylinders.
Purge Procedure (Steering System)
- Start the engine and operate the engine at low idle.
- Align the left-hand joystick control so that the joystick control will match the steering angle of the front wheels.
- Move the left-hand joystick control all the way to the left and hold for 30 seconds.
- Move the left-hand joystick control all the way to the right and hold for 30 seconds.
- Shut off the engine.
- Remove the parts that are listed in Table 1 from locations (1) and (2).
- Check the oil level in the hydraulic tank.
Caterpillar Information System:
C15 and C18 Tier 4 Final Engines Engine Oil Pressure - Test
C9.3 Engines for Caterpillar Built Machines Sensor Calibration Required - Test
Product Link - PL522/523 Configuration
Product Link - PL522/523 System Components
Product Link - PL522/523 System Overview
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Hydraulic and Steering System Pump Control Valve (Implement, Steering) - Test and Adjust
C27 and C32 Tier 4 Engines Diagnostic Capabilities
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Hydraulic and Steering System Pilot Pressure - Test and Adjust
C18 Generator Set Engine Oil and Filter - Change
793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) MID 162 - CID 2183 - FMI 13
793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) MID 162 - CID 0890 - FMI 09
793F Series AC, 795F Series AC and 795F Series AC XQ Off-Highway Trucks VIMS 3G, Monitoring, and Truck Payload Measurement System (TPMS) MID 161 - CID 0246 - FMI 09
C7.1 Industrial Engine and Generator Set ARD Failed to Ignite
2010/07/02 New Bolts Are Available for the Clutch Disc Inside the Torque Converter on Large Wheel Loaders, Landfill Compactors, and Wheel Dozers {3101}
C27 and C32 Engines for Caterpillar Built Machines Aftercooler - Test - If Equipped
Product Link - PL522/523 Installation Parameters Configure
Product Link - PL522/523 Spare Input Configure
Product Link - PL522/523 Commands
797 and 797B Off-Highway Truck/Tractors Braking System Retarder Function
Product Link - PL522/523 General Information
259B3 Compact Track Loader, 247B3 and 257B Series 3 Multi Terrain Loaders and 216B Series 3, 226B3, 236B3, 242B Series 3 and 252B Series 3 Skid Steer Loaders Piston Motor (Hydrostatic)
C13, C15, and C18 Tier 4 Interim Engines Exhaust Balance Valve - Test
259B3 Compact Track Loader, 247B3 and 257B Series 3 Multi Terrain Loaders and 216B Series 3, 226B3, 236B3, 242B Series 3 and 252B Series 3 Skid Steer Loaders Piston Motor (Hydrostatic)
795F AC Off-Highway Truck Automatic Lubrication System (For Electric Start Equipped Trucks) Automatic Lubrication System Troubleshooting