Transmission and Transfer Gears - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-9204 | 操纵杆滚轮举倾机构 | 1 |
开始:
- 拆下后驱动轴护罩。
Show/hide table
车斗降下后,车斗与机架之间没有空隙。 如果不安装固定缆线,可能会导致在此区域作业的人员受伤或死亡。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
- 安装车轮楔子。 请参阅操作和保养手册, "车轮楔子的使用"。
- 安装车斗固定拉线。 请参阅操作和保养手册, "拉线(车斗固定)"。
- 将变速箱中的油排入适当的容器中以便保存或处理。 有关正确的排放和加注过程,请参考操作和保养手册, "变矩器和变速箱油- 更换"。
Show/hide table
图 1 g03247279 - 将适当的起吊设备连接到传动轴 (1) 上。 传动轴 (1) 的重量约为
145 kg (320 lb) 。 - 拆下螺栓 (2 )。 弃置螺栓 (2)。
注: 螺栓 (2) 不可重复使用。 弃置螺栓 (2)。
- 使用合适的撬杆缩回传动轴 (1)。 使用合适的垫块支撑传动轴 (1)。
Show/hide table
图 2 g03247297 - 断开软管组件 (3) 和软管组件 (4)。
Show/hide table
图 3 g03247301 - 拆下护罩 (5)。 断开线束组件 (6)。
Show/hide table
图 4 g03247314 - 断开线束组件 (7)。 拆下卡箍 (8)。 断开软管组件 (9)。
Show/hide table
图 5 g03247316 - 断开软管组件 (10)。
Show/hide table
图 6 g03247321 Show/hide table图 7 g03247323 - 将工具 (A) 和适当的起吊设备连接到变速箱和分动器 (11) 上。 变速箱和分动器 (11) 的重量约为
2109 kg (4650 lb) 。 - 拆下支架 (12)。 拆下螺栓 (13)。 拆下变速箱和分动器 (11)。
- 按照与拆卸相反的顺序安装变速箱和分动器 (11)。
- 使用以下步骤将万向节啮合到分动器的轭上。
注: 安装传动轴时,在将万向节落座到分动器上之前,先切割将滑动接头固定到一起的焊丝。
- 使万向节的销和定位孔与分动器的轭啮合。 使用适当的橡胶或木锤使万向节完全落座。
- 安装新螺栓 (2)。
- 按交替 (X) 方式拧紧螺栓 (2) 至扭矩为
775 ± 40 N·m (572 ± 30 lb ft) 。 - 再次以交替 (X) 方式拧紧螺栓 (2) 至扭矩为
775 ± 40 N·m (572 ± 30 lb ft) ,以确保达到正确的扭矩。 - 拧紧螺栓 (13) 至扭矩为
530 ± 70 N·m (391 ± 52 lb ft) 。
Caterpillar Information System:
797F and 797F XQ Off-Highway Truck Braking System Piston Pump (Brake Cooling) - Extra Retarding
797F and 797F XQ Off-Highway Truck Power Train Gear Pump (Brake Cooling, Brake Actuation and Rear Axle Motor Drive)
797F and 797F XQ Off-Highway Truck Braking System Motor Rotating (Brake Cooling) - Extra Retarding
797F and 797F XQ Off-Highway Truck Braking System Piston Motor (Brake Cooling) - Extra Retarding
797F and 797F XQ Off-Highway Truck Power Train Gear Pump (Brake, Rear Axle Lubrication) - Extra Retarding
2009/08/03 Special Instruction for the Heated Body Kit is Available for Articulated Trucks {1061}
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System Fill Time for the Transmission Clutch - Calibrate
584 and 584HD Forwarders Camera - Clean/Adjust - If Equipped
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System Engagement Pressure for the Transmission Clutch - Calibrate
793F Off-Highway Truck Power Train Axle Shaft - Remove
793F and 797F Off-Highway Trucks Power Train Electronic Control System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
2009/09/28 New Software Released For AccuGrade Office {5267, 7220}
CD44B and CD54B Vibratory Asphalt Compactors Alternator - Inspect
2009/08/03 Pistons and Piston Rings {1225, 1225}
M325D L MH and M325D MH Material Handlers Hydraulic System Swing Bearing Movement - Measure
2009/07/20 Method for Monitoring The Landfill Compactor Tip Assembly ( 7 inch step ) {4206, 6806}
2011/01/06 Improvements to the Fuel Sender Group {1273, 1408, 6201, 7481, 7857}
2009/07/27 New Bumpers Are Now Used on Cab Doors {7308}
770 and 772 Off-Highway Truck Camera - If Equipped
2009/09/07 Rework Procedure to Reinforce the Mounting of the Cowl {7051, 7155, 7251, 7254, 7267}
Rework Procedure to Reinforce the Cowl Assembly{0679, 7051, 7155, 7251, 7254, 7267} Rework Procedure to Reinforce the Cowl Assembly{0679, 7051, 7155, 7251, 7254, 7267}
797F and 797F XQ Off-Highway Truck Hydraulic System Control Valve (Brake Cooling, Hoist)
M325D L MH and M325D MH Material Handlers Hydraulic System Travel Motor (Destroke Point) - Test and Adjust
854G Wheel Dozer Secondary Steering - Test