Idler Gear - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 230-6284 | 定时销(凸轮轴) | 1 |
B | 230-6283 | 定时销(曲轴) | 1 |
C | 9U-7324 | 千分表支架 | 1 |
7H-1942 | 千分表 | 1 | |
3S-3268 | 千分表触针 | 1 | |
7H-1940 | 通用附件 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保 1 号活塞在压缩冲程的上死点位置。 请参阅系统操作、测试和调整 , "确定 1 号活塞上止点位置 "。
Show/hide table
图 1 g01473492 定时标记的对齐 - 确保已将工具 (A) 安装在凸轮轴齿轮 ( 1) 的孔 (X) 中。
- 确保已将工具 (B) 安装在前壳体的孔 ( Y) 中。 使用工具 (B),将曲轴锁定到位。
Show/hide table
图 2 g01473634 典型实例 Show/hide table图 3 g01473635 典型实例 - 清洁惰轮 (5) ,检查惰齿轮是否磨损或损坏。 有关更多资料,请参阅 技术规格, "齿轮总成(前) "。 如有必要,更换惰轮。
- 清洁轮毂 (4),检查轮毂是否磨损或损坏。 有关更多资料,请参阅 技术规格, "齿轮总成(前) "。 如有必要,更换轮毂。
- 使用清洁的发动机机油润滑轮毂 ( 4) 。 将轮毂滑入惰轮 ( 5)。 确保定时标记朝向惰轮前部。
- 使惰轮 (5) 与凸轮轴齿轮上的定时标记对齐。 请参阅插图 1。 将惰轮组件 ( 5) 和轮毂 (4) 安装到定时箱的凹槽中。 确保油孔 (Z) 在轮毂顶部。
注: 在安装过程中惰轮必须保持倾斜。 确保轮毂中的孔与缸体中的孔对齐。
- 清洁盘 (2),检查盘是否磨损或损坏。 如有必要,更换盘。
- 使用清洁的发动机机油润滑盘 ( 2)。 应将旧盘安装在原来的方向。 如果要安装新盘,确保对齐盘 ( 2) 中的孔与轮毂 (4) 中的孔。 将盘 (2) 安装到轮毂 ( 4) 上。
- 安装螺栓 (3)。 将螺栓拧紧至扭矩
44 N·m (32 lb ft) 。Show/hide table图 4 g01269936 使用一套塞尺检查端隙。 - 使用一套塞尺,检查惰轮的端隙。 有关更多资料,请参阅 技术规格, "齿轮总成(前) "。
- 使用工具 (C) 检查惰轮与凸轮轴齿轮之间的齿隙。 有关更多资料,请参阅 技术规格, "齿轮总成(前) "。
- 使用工具 (C) 检查惰轮与曲轴齿轮之间的齿隙。 有关更多资料,请参阅 技术规格, "齿轮总成(前) "。
- 使用清洁的发动机机油稍微润滑所有的齿轮。
结束:
- 安装喷油泵齿轮。 请参阅拆解和组装燃油泵齿轮 -, "安装" 。
- 如果发动机配备空气压缩机,则安装该空气压缩机。 请参阅拆解和组装 , "空气压缩机 - 拆卸和安装" 。
- 如果发动机配备真空泵,则安装该真空泵。 请参阅拆解和组装真空泵 , "- 拆卸和安装" 。
- 如果发动机配备附件驱动,则安装该附件驱动。 请参阅拆解和组装附件驱动 - 拆卸和安, "装"。
Caterpillar Information System:
CD54 Vibratory Compactor Machine Systems Rollover Protective Structure (ROPS)
C4.4 Industrial Engine Idler Gear - Remove
C4.4 Industrial Engine Idler Gear - Remove
CD54 Vibratory Compactor Machine Systems Piston Motor (Vibratory)
CD54 Vibratory Compactor Machine Systems Gear Motor (Fan Drive)
MINEGEM Machine Control ; Guidance Products Machine Automation System Visual Inspection
MINEGEM Machine Control ; Guidance Products Local Area Radio Network Visual Inspection
2009/03/23 Installation Procedure for the Brake Group Seal Assemblies {4251, 4267}
MINEGEM Machine Control ; Guidance Products Area Isolation System Area Isolation System Troubleshooting
MINEGEM Machine Control ; Guidance Products Area Isolation System Visual Inspection
795F AC and 795F AC XQ Off-Highway Trucks Fuses, Circuit Breakers and Relays - Replace/Reset
2009/03/23 Correction to Disassembly and Assembly , "Service Brake - Disassemble" {4251}
C4.4 Industrial Engine Idler Gear - Install
CD54 Vibratory Compactor Machine Systems Hydraulic Cylinder (Steering)
CD54 Vibratory Compactor Machine Systems Operator Platform
795F AC and 795F AC XQ Off-Highway Truck Power Train Final Drive Oil Cooler
2009/03/02 Clarification to The Assembly Procedure for 120M, 140M, and 160M Front Gear Groups on All Wheel Drive Machines {4053, 4205, 4208, 4350, 4351, 4355}
Motor Grader Circle Pinion Reuse {5207} Motor Grader Circle Pinion Reuse {5207}
793F and 793F CMD Off-Highway Truck Automatic Lubrication System General Information
CB-214E, CB-224E and CB-225E Paving Compactors Maintenance Interval Schedule
Bench Test Procedure for a 120H, 12H, 12K, 135H, 140H, 140K, 143H, 160H, 160K, and 163H Motor Grader Transmission{3030, 3073, 3139} Bench Test Procedure for a 120H, 12H, 12K, 135H, 140H, 140K, 143H, 160H, 160K, and 163H Motor Grader Transmission{3030, 3073, 3139}
2009/07/13 New Hoses Are Now Used On Some Medium Wheel Loaders {4304}
2009/03/09 An Improved O-Ring Seal is Now Used in the Transmission Clutch Solenoid Modulating Valves {3073, 3167}
Install Both the 340-4329 Fan Guard and the 340-4325 Fan Support At the Same Time{1356, 1360} Install Both the 340-4329 Fan Guard and the 340-4325 Fan Support At the Same Time{1356, 1360}