Gear Pump (Transmission Charging and Scavenge) - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
注: 检查所有部件和所有 O 形密封圈是否磨损或损坏。 如有必要,请更换部件。 在密封的地方,用润滑油将 O 形密封圈稍加润滑。
- 冷却两个轴承 (16) 。 使用工具 (A) 将轴承 (16) 安装到盖 (17) 中。 标记轴承接头的位置。 如图所示,安装轴承 (16) 时,轴承接头必须距中心线 30 ± 15 度。 如图所示,安装轴承 (16) ,直到轴承 (16) 处于平面 (Z) 以下 1.50 ± 0.25 mm (0.059 ± 0.010 in)。
Show/hide table
图 1 | g00621189 |
Show/hide table
图 2 | g00622512 |
- 将泵体组件 (15) 、四个定位销(未显示)和 O 形密封圈安装在泵盖组件 (17) 上。
- 冷却两个轴承 (14) 。 使用工具 (A) 将轴承安装到机油泵体组件 (8) 中。 标记轴承接头的位置。 如图所示,安装轴承 (16) 时,轴承接头必须距中心线 30 ± 15 度。 如图所示,安装轴承 (16) ,直到轴承 (16) 处于平面 (Y) 以下 1.50 ± 0.25 mm (0.059 ± 0.010 in)。
Show/hide table
图 3 | g00621184 |
Show/hide table
图 4 | g00622513 |
- 将两个月牙键(未显示)安装在机油泵齿轮组件中及机油泵齿轮 (13) 底下。
- 将两个机油泵齿轮 (13) 安装在机油泵齿轮组件 (10) 和机油泵齿轮组件 (12) 的原有位置。
- 将机油泵齿轮组件 (10) 和机油泵齿轮组件 (12) 安装在机油泵体组件 (8) 的原有位置。
- 如图所示,定位机油泵体组件 (8) 。
Show/hide table
图 5 | g00621183 |
- 将月牙键 (9) 安装在机油泵齿轮组件 (12) 上。
- 将两个机油泵齿轮 (11) 安装在机油泵齿轮组件 (10) 和机油泵齿轮组件 (12) 上。
- 将机油泵体组件 (8) 和 O 形密封圈安装在齿轮泵 (3) 上。
Show/hide table
图 6 | g00621182 |
- 将两个定位销(未显示)安装在泵歧管组件 (7) 上。
Show/hide table
图 7 | g00621181 |
- 将泵歧管组件 (7) 和 O 形密封圈安装在齿轮泵 (3) 上。
注: 将八个橡皮垫圈其中的一个组装在钢垫圈的每一侧以及螺栓 (6) 上。
- 将四个螺栓 (6) 、八个橡皮垫圈和四个钢垫圈安装在齿轮泵 (3) 中。
- 将两个 O 形密封圈 (5) 安装在齿轮泵 (3) 中。
- 如图所示,定位齿轮泵 (3) 。
Show/hide table
图 8 | g00621180 |
- 将两个螺栓 (4) 和垫圈安装在齿轮泵 (3) 中。
- 将磁性滤网 (2) 和 O 形密封圈定位在齿轮泵 (3) 上。
Show/hide table
图 9 | g00621178 |
- 将三个螺栓 (1) 安装在磁性滤网 (2) 上。
- 运转之前先使用液压油润滑齿轮泵 (3) 。 核实齿轮泵 (3) 转动自如。
End By: 安装齿轮泵。 请参阅 拆解和装配, "齿轮泵(变速箱注油和回油)- 安装",了解正确的步骤。
Caterpillar Information System:
12K, 140K and 160K Motor Graders Power Train Gear Pump (Transmission Charging and Scavenge) - Disassemble
12K, 140K and 160K Motor Graders Power Train Gear Pump (Transmission Charging and Scavenge) - Remove
CB54 and CB64 Asphalt Compactors Machine Systems Battery and Battery Cable - Separate and Connect
2008/12/01 Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
277C, 277C2, 287C, 287C2 and 297C Multi Terrain Loaders Machine Systems Undercarriage
3408E and 3412E Engines for Caterpillar Built Machines Engine Stalls at Low RPM
2009/02/23 Updated Bracket for the Hydraulic Lines {4304, 5057}
2008/12/01 Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1326 - FMI 02
3408E and 3412E Engines for the 844 Wheel Dozer and for 988F Series II and 990 Series II Wheel Loaders Engine Shutdown Is Intermittent
2009/01/26 K Series Bucket Tip Slag Retainers For High Temperature Applications are Available {6805}
EquipmentManager User Guide Manage Major Repair Tracking
795F AC and 795F AC XQ Off-Highway Truck Engine Supplement Battery - Remove and Install
2008/12/01 Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
12K, 140K and 160K Motor Graders Power Train Gear Pump (Transmission Charging and Scavenge) - Install
C9 Engines for Motor Graders Engine Top Speed Is Not Obtained
CB54 and CB64 Asphalt Compactors Machine Systems Piston Motor (Drum Propel) - Remove - Rear
2008/12/29 A Standard Procedure For Measuring Cylinder Drift Has Been Published {7562}
CB54 and CB64 Asphalt Compactors Machine Systems Piston Motor (Drum Propel) - Install - Rear
CB54 and CB64 Asphalt Compactors Machine Systems Piston Motor (Drum Propel) - Disassemble - Rear
CB54 and CB64 Asphalt Compactors Machine Systems Piston Motor (Drum Propel) - Assemble - Rear
CB54 and CB64 Asphalt Compactors Machine Systems Piston Motor (Drum Propel) - Remove - Front
CB54 and CB64 Asphalt Compactors Machine Systems Piston Motor (Drum Propel) - Disassemble - Front
CB54 and CB64 Asphalt Compactors Machine Systems Piston Motor (Drum Propel) - Assemble - Front