Circuit Breakers - Reset
Show/hide table
| PERHATIAN |
|---|
Ganti pemecah sirkuit hanya dengan jenis dan ukuran yang sama. Kalau tidak, dapat mengakibatkan kerusakan kelistrikan. Jika acapkali perlu menyetel ulang pemecah sirkuit, mungkin ada masalah kelistrikan. Hubungi dealer Caterpillar Anda. |
Show/hide table
| Pemutus Sirkuit - Tekan tombol untuk menyetel ulang pemutus sirkuit. Bila sistem kelistrikan bekerja dengan baik, tombol akan tetap berada dalam posisi tertekan. Bila tombol kembali terdorong keluar, periksalah sirkuit kelistrikan yang berhubungan. Lakukan perbaikan sirkuit kelistrikan, apabila diperlukan. |
Show/hide table
 | |
| Ilustrasi 1 | g01230028 |
Panel pemutus sirkuit terletak di sisi kanan ruangan operator.
Show/hide table
 | |
| Ilustrasi 2 | g01230030 |
Show/hide table
| (1) Modul Kontrol Engine Elektronik (ECM) - 15 Amp |
Show/hide table
| (1) Kunci Kontak |
Show/hide table
| (1) Lubang Servis |
Show/hide table
| (1) Timer Pemberhentian Idle |
Show/hide table
| (2) Lampu Kubah (Jika Dilengkapi) - 15 Amp |
Show/hide table
| (3) Lampu Kanan Depan - 30 Amp (Otomatis) |
Show/hide table
| (3) Lampu Kanan Belakang |
Show/hide table
|
| (4) Lampu Kiri Depan - 30 Amp (Otomatis) |
Show/hide table
|
| (4) Lampu Kiri Belakang |
Show/hide table
| (5) Modul Kontrol Elektronik (ECM) Power Train - 15 Amp |
Show/hide table
 | |
| Ilustrasi 3 | g01230316 |
Show/hide table
|
| (6) Lubang Servis - 30 Amp |
Show/hide table
| (6) Sistem Kontrol Jauh (Jika Dilengkapi) |
Show/hide table
| (7) Monitor, Lubang Telemetri, Modul Akses Elektronik (EAM) - 15 Amp |
Show/hide table
| (7) Sensor Tekanan Oli Transmisi |
Show/hide table
| (7) Pencahayaan Instrumen |
Show/hide table
| (7) Sistem Monitoring Caterpillar |
Show/hide table
| (8) Cadangan (24v) - 15 Amp |
Show/hide table
| (8) Sistem Pelumasan Otomatis (Jika Dilengkapi) |
Show/hide table
| (8) Tekanan Gas Buang (Jika Dilengkapi) |
Show/hide table
|
| (9) Sistem Kontrol Jauh (Jika Dilengkapi) - 15 Amp |
Show/hide table
| (10) Sistem Kontrol Payload (Jika Dilengkapi) - 15 Amp |
Show/hide table
| (10) Pengubah 24V ke 12V |
Show/hide table
| (11) Air Conditioner (Jika Dilengkapi) - 15 Amp |
Show/hide table
| (12) Klakson - 15 Amp |
Show/hide table
|
| (12) Sistem Pelumasan Otomatis (Jika Dilengkapi) |
Show/hide table
| (13) Washer dan Wiper Jendela Depan - 15 Amp |
Show/hide table
| (13) Washer dan Wiper Jendela Samping |
Show/hide table
| (13) Washer dan Wiper Jendela Belakang |
Show/hide table
| (13) Radio (Aksesoris) (Jika Dilengkapi) |
Show/hide table
|
| (14) Modul Kontrol Elektronik (ECM) Power Train - 15 Amp |
Show/hide table
 | |
| Ilustrasi 4 | g01233544 |
(15) 105 Amp - Alternator.
(16) 80 Amp - Utama.
Caterpillar Information System:
EquipmentManager Dealer Administrator Manual Active Fleet
14H and 16H Motor Graders Hydraulic and Steering System Pump Efficiency (Gear Pumps) - Test
416E Backhoe Loader Loader Bucket, Cylinder, and Linkage Bearings - Lubricate
416E Backhoe Loader Lift Cylinder Brace - Connect and Disconnect
2008/11/01 Policy on Testing of Fuel Injectors and Fuel Nozzles {1251}
2008/11/17 Policy on Testing of Fuel Injectors and Fuel Nozzles {1251}
797B Off-Highway Truck Mirror
416E Backhoe Loader Shipping the Machine
416E Backhoe Loader Leaving the Machine
12K, 140K, 140K Series 2 and 160K Motor Graders Hydraulic and Steering System Steering System
416E Backhoe Loader Stabilizer Control
416E Backhoe Loader Backup Alarm
R2900G Load Haul Dump Circuit Breakers - Reset
2009/02/23 New Oil Pump {1151, 1162, 1206}
CB54, CB54 XW and CB64 Vibratory Compactor Propel System Brake Pump
793F and 797F Off-Highway Trucks Chassis Electronic Control System System Schematic
2008/12/01 Water Temperature Regulator {1355, 1380}
IT38H Integrated Toolcarrier and 938H Wheel Loader Alternator Air Vent Line and Screen - Clean
416E Backhoe Loader Alternate Exit
The Procedure for Servicing the Air Cleaner on Articulated Trucks{1051, 1054} The Procedure for Servicing the Air Cleaner on Articulated Trucks{1051, 1054}
2008/12/29 New Software Prevents the Discrepancy Between the Display on the Monitor and the Service Hour Meter Reading for Certain Excavators {7490, 7601, 7610, 7620}
2008/12/01 A New Bearing is Now Used on the Support for the Conveyor on Certain Cold Planers {7074}
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Cranks but Will Not Start
2008/12/29 An Improved Solenoid Valve Is Now Used {5132, 5479}