430E Backhoe Loader Caterpillar

Specifications

Illustration 1	g01628153

Note: The sleeve bearings and the bore for the sleeve bearing must be clean, free of rust, primer and paint. Make sure that the sleeve bearings are flush to the surface.

(1) 213-6687 Sleeve Bearing

Inside diameter ... 50.302 ± 0.020 mm (1.9804 ± 0.0008 inch)

Outside diameter ... 63.094 ± 0.013 mm (2.4840 ± 0.0005 inch)

(2) 9R-0170 Bearing

Inside diameter ... 55.309 ± 0.020 mm (2.1775 ± 0.0008 inch)

Outside diameter ... 68.105 ± 0.013 mm (2.6813 ± 0.0005 inch)

(3) 9R-0162 Sleeve Bearing

Inside diameter ... 50.302 ± 0.020 mm (1.9804 ± 0.0008 inch)

Outside diameter ... 63.094 ± 0.013 mm (2.4840 ± 0.0005 inch)

(4) One washer per side is required. Use the following washer in order to provide a maximum total clearance of 4.0 mm (0.1575 inch):

9R-1510 Washer

Thickness of one washer ... 4.0 mm (0.16 inch)

(5) 154-5278 Pin

Pin diameter ... 49.950 to 50.000 mm (1.9665 to 1.9684 inch)

(6) 9R-0170 Bearing

Inside diameter ... 55.309 ± 0.020 mm (2.1775 ± 0.0008 inch)

Outside diameter ... 68.105 ± 0.013 mm (2.6813 ± 0.0005 inch)

(7) 213-6698 Pin

Pin diameter ... 54.950 to 55.000 mm (1.9665 to 1.9684 inch)

(8) One washer per side is required. Use the following washer in order to provide a maximum total clearance of 4.0 mm (0.16 inch):

9R-1502 Washer

Thickness of one washer ... 4 mm (0.16 inch)

(9) 213-6703 Bearing

Inside diameter ... 45.295 ± 0.02 mm (1.7833 ± 0.0008 inch)

Outside diameter ... 58.082 ± 0.013 mm (2.2867 ± 0.0005 inch)

(10) One washer per side is required. Use the following washer in order to provide a maximum total clearance of 3 mm (0.12 inch):

9R-0158 Washer

Thickness of one washer ... 3 mm (0.12 inch)

(11) 154-5279 Pin

Pin diameter ... 44.950 to 45.00 (1.7696 to 1.7755)

(12) 154-5280 Pin

Pin diameter ... 49.950 to 50.000 mm (1.9665 to 1.9684 inch)

Removal Procedure

1. Remove the hoe bucket.

2. Place the stick on the ground.

Show/hide table



Illustration 2	g01632793

3. Attach a suitable lifting device to link assembly (1) . The weight of link assembly (1) is approximately 25 kg (55 lb). Remove pin (2) and link assembly (1) .

Show/hide table



Illustration 3	g01633513

4. Remove bearings (3) and (4) from both sides of link assembly (1) .

Show/hide table



Illustration 4	g01633533

Note: Note the number and the location of the shims.

5. Remove retaining rings (5) and (7) . Remove link assembly (6) . Repeat for the opposite side.

Show/hide table



Illustration 5	g01633572

6. Use Tooling (A) in order to remove bearings (8) and (9) from both link assemblies (6) .

Installation Procedure

Show/hide table



Illustration 6	g01633577

1. Lower the temperature of bearings (8) and (9) . Use Tooling (A) in order to install bearings (8) and (9) into both link assemblies (6) .

   Note: Make sure that bearings (8) and (9) are flush with Surface (X) during the installation process.

Show/hide table



Illustration 7	g01633533

2. Install link assemblies (6) . Install shims in order to obtain a maximum total clearance of 4.0 mm (0.16 inch). Install retaining rings (5) and (7) .

   Note: Note that one shim is required on each side.

Show/hide table



Illustration 8	g01633612

3. Lower the temperature of bearings (3) and (4) . Use Tooling (A) in order to install bearings (3) and (4) into both sides of link assembly (1) .

   Note: Make sure that bearings (3) and (4) are flush with Surface (Y) during the installation process.

Show/hide table



Illustration 9	g01632793

4. Attach a suitable lifting device to link assembly (1) . The weight of link assembly (1) is approximately 25 kg (55 lb). Install link assembly (1) . Install pin (2) .

End By: Install the hoe bucket. Install the required amount of shims in order to maintain a maximum total clearance of 3.0 mm (0.12 inch).