Axle Housing and Flange - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-2320     | Combination Puller     | 1     |
B     | 230-7923     | Spanner Wrench As.     | 1     |
C     | 2P-8312     | Retaining Ring Pliers     | 1     |
Start By:
- Remove the final drive planetary. Refer to Disassembly and Assembly, "Final Drive Planetary - Remove".
- Loosen nut (1) . Do not remove nut (1) at this time. Install Tooling (A) . Remove tie rod end (2) from the taper of the knuckle. Remove nut (1) and position tie rod end (2) out of the way.
Show/hide table
Illustration 1 | g01632395 |
- Remove bolts (5) and remove locking plate (4) . Use Tooling (B) in order to remove spanner nut (3) .
Show/hide table
Illustration 2 | g01047569 |
- Use a suitable pry bar and push the double U-joint toward the wheel flange. This will make the removal of retaining ring (8) easier. Use Tooling (C) and remove retaining ring (8) . Remove thrust washer (7) and washer (6) .
Show/hide table
Illustration 3 | g01023074 |
Show/hide table
Illustration 4 | g01023075 |
- Remove ring gear (9) .
Show/hide table
Illustration 5 | g01023088 |
- Remove wheel flange (10) .
Note: Bearing cone (11) will fall out of wheel flange (10) when wheel flange (10) is removed.
Show/hide table
Illustration 6 | g01023126 |
- Remove bolts (12) . Remove pin assembly (13) and shims (14) . Remove bolts (16) and pin assembly (15) .
Show/hide table
Illustration 7 | g01023130 |
Note: Note the order and orientation of shims (14) for assembly purposes.
- Use a suitable lifting device in order to remove knuckle (17) . The weight of knuckle (17) is approximately 50 kg (110 lb).
Show/hide table
Illustration 8 | g01023136 |
Caterpillar Information System:
C9.3 Engines for Caterpillar Built Machines Cooling System
2008/11/10 A NewWarning Indicator Module Group is Available on Some Backhoe Loaders {1408, 7407, 7431}
Setup and Configuration for Health Interface Module (HIM) Component Description
Setup and Configuration for Health Interface Module (HIM) Configuration Validation
Setup and Configuration for Health Interface Module (HIM) Configuration
Setup and Configuration for Health Interface Module (HIM) Computer Setup
Setup and Configuration for Health Interface Module (HIM) General Information
AccuGrade For Wheel Tractor-Scrapers Electrical Power Supply (Angle Sensor)
AccuGrade For Wheel Tractor-Scrapers Electrical Power Supply (Data Radio)
2008/09/01 New Plate Assembly Is Now Used {7301}
2008/09/01 A New Procedure is Available to Install a New Axle on Soil Compactors {3282}
2008/08/25 New Engine Wiring Harnesses Are Used {1408}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Axle Housing and Flange - Install
430E Backhoe Loader Backhoe Bucket Linkage - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Vibration Damper
CD54 Vibratory Compactor Machine Systems Cab - Remove
CD54 Vibratory Compactor Machine Systems Cab - Install
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Piston Pump (Steering) - Remove
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Piston Pump (Steering) - Install
2009/11/02 A New Turbocharger and New Engine Software Are Now Used on 770 Off-Highway Trucks {1000, 1052, 1053, 1901, 1920}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Axle Housing (Differential and Bevel Gear) (Front) - Install
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Axle Housing (Differential and Bevel Gear) (Front) - Remove
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Axle Housing (Differential and Bevel Gear) (Front) - Install
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Electrohydraulic System Piston Pump (Implement) (Pilot)