Axle Housing and Flange - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
B     | 230-7923     | Spanner Wrench As     | 1     |
C     | 2P-8312     | Retaining Ring Pliers     | 1     |
D     | 129-1938     | Grease Cartridge     | -     |
- Use a suitable lifting device in order to install knuckle (17) . The weight of knuckle (17) is approximately 50 kg (110 lb).
Show/hide table
Illustration 1 | g01023136 |
- Do not install shims (14) at this time. Install pin assembly (13) . Install bolts (12) . Do not tighten bolts (12) at this time.
Show/hide table
Illustration 2 | g01023130 |
- Apply Tooling (D) to the surface of pin assembly (15) . Install pin assembly (15) and bolts (16) . Tighten bolts (16) to a torque of 300 N·m (221 lb ft).
- Install wheel flange (10) and bearing cone (11) .
Show/hide table
Illustration 3 | g01023126 |
- Install ring gear (9) .
Show/hide table
Illustration 4 | g01023088 |
- Use Tooling (B) and install spanner nut (3) . Tighten spanner nut (3) to a torque of 1000 N·m (738 lb ft). Install locking plate (4) and bolts (5) . Tighten bolts (5) to a torque of 70 N·m (52 lb ft).
Note: If the tab on locking plate (4) does not line up with the slot in spanner nut (3) , tighten spanner nut (3) until the slot and the tab are aligned.
Show/hide table
Illustration 5 | g01047569 |
- Use a suitable pry bar and push the double U-joint toward the wheel flange. This will make the installation of retaining ring (8) easier. Install washer (6) and thrust washer (7) . Use Tooling (D) and install retaining ring (8) .
Show/hide table
Illustration 6 | g01023074 |
Show/hide table
Illustration 7 | g01023075 |
- Insert a suitable pry bar and move the knuckle up and down while you tighten bolts (12) . Tighten bolts (12) until there is no end play. Use a suitable feeler gauge and measure the clearance between pin assembly (13) and the knuckle. Measure the clearance at several points and average the measurement. Use shims (14) that equal the measurement.
Show/hide table
Illustration 8 | g01029956 |
- Remove pin assembly (13) . Apply Tooling (D) to the surface of pin assembly (13) . Install pin assembly (13) , the correct shims (14) , and bolts (12) . Tighten bolts (12) to a torque of 300 N·m (221 lb ft).
- Install tie rod end (1) into the axle housing. Install nut (2) . Tighten nut (2) to a torque of 280 N·m (205 lb ft).
Show/hide table
Illustration 9 | g01632395 |
End By: Install the final drive planetary. Refer to Disassembly and Assembly, "Final Drive Planetary - Install".
Caterpillar Information System:
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Axle Housing and Flange - Remove
C9.3 Engines for Caterpillar Built Machines Cooling System
2008/11/10 A NewWarning Indicator Module Group is Available on Some Backhoe Loaders {1408, 7407, 7431}
Setup and Configuration for Health Interface Module (HIM) Component Description
Setup and Configuration for Health Interface Module (HIM) Configuration Validation
Setup and Configuration for Health Interface Module (HIM) Configuration
Setup and Configuration for Health Interface Module (HIM) Computer Setup
Setup and Configuration for Health Interface Module (HIM) General Information
AccuGrade For Wheel Tractor-Scrapers Electrical Power Supply (Angle Sensor)
AccuGrade For Wheel Tractor-Scrapers Electrical Power Supply (Data Radio)
2008/09/01 New Plate Assembly Is Now Used {7301}
2008/09/01 A New Procedure is Available to Install a New Axle on Soil Compactors {3282}
430E Backhoe Loader Backhoe Bucket Linkage - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Vibration Damper
CD54 Vibratory Compactor Machine Systems Cab - Remove
CD54 Vibratory Compactor Machine Systems Cab - Install
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Piston Pump (Steering) - Remove
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Piston Pump (Steering) - Install
2009/11/02 A New Turbocharger and New Engine Software Are Now Used on 770 Off-Highway Trucks {1000, 1052, 1053, 1901, 1920}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Axle Housing (Differential and Bevel Gear) (Front) - Install
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Axle Housing (Differential and Bevel Gear) (Front) - Remove
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Axle Housing (Differential and Bevel Gear) (Front) - Install
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Electrohydraulic System Piston Pump (Implement) (Pilot)
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Pilot Oil Accumulator - Test and Charge