Piston Motor (Propel) - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 136-1452 | Retaining Ring Pliers As | 1 |
- Lower the temperature of rotating group (30).
- Install rotating group (30) into housing (31).
- Install spacer (29).
- Use Tooling (A) in order to install retaining ring (28).
- Use a suitable press in order to press rotating group (30) against retaining ring (28).
- Install gasket (27).
Show/hide table
Illustration 3 g01181043 - Install housing (25) and bolts (26).
- Install O-ring seal (23).
- Use Tooling (A) in order to install retaining ring (24).
Show/hide table
Illustration 4 g01181042 - Install seal (22).
Show/hide table
Illustration 5 g01181041 - Install cover (21).
- Use Tooling (A) in order to install retaining ring (20).
Show/hide table
Illustration 6 g01181040 - Install pins (18) and bearings (19).
Show/hide table
Illustration 7 g01181039 - Install spider assembly (17).
Show/hide table
Illustration 8 g01181038 - Install bearing (15), barrel (16), and port plate (14).
Show/hide table
Illustration 9 g01181037 - Install plate (13).
Show/hide table
Illustration 10 g01181036 - Install O-ring seals (11) and piston (12).
Show/hide table
Illustration 11 g01181035 - Install cover (10) and bolts (9).
Show/hide table
Illustration 12 g01181034 - Install spool (6).
- Install retainer (7) and spring (8).
Show/hide table
Illustration 13 g01181033 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install plug (5).
- Install plug (4).
- Repeat Step 20 through Step 21 for the opposite side.
Show/hide table
Illustration 14 g01181032 - Install gasket (3).
Show/hide table
Illustration 15 g01181031 - Install head (2) and bolts (1).
Show/hide table
Illustration 1 | g01182025 |
Show/hide table
Illustration 2 | g01181046 |
End By:
- Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Propel) - Install".
Caterpillar Information System:
AP555E and BG555E Asphalt Pavers Machine Systems Piston Motor (Propel) - Disassemble
432E, 434E, 442E and 444E Backhoe Loaders Specifications
793F Off-Highway Truck Power Train Modulating Valve (Transmission Clutch Engaging) - Disassemble
3512C Engine and 785D Off-Highway Truck/Tractors Diagnostic Trouble Codes
432E, 434E, 442E and 444E Backhoe Loaders Rated Load
AS4251C Asphalt Screed Shoe (End Gate) - Remove and Install
AS4251C Asphalt Screed Screed Frame (Extender) - Remove and Install
2008/05/19 A New Gasket is Available for Mounting of the Air Starting Motor {1451, 7555}
AP600D Asphalt Paver Propel System Piston Pump Neutral - Test and Adjust
422E and 428E Backhoe Loaders Swing Lock Pin Control
422E and 428E Backhoe Loaders Work Tool Flow Control - If Equipped
24M Motor Grader Power Train Rear Axle, Differential and Final Drive - Install
AP600D and BG600D Asphalt Pavers Machine Systems Piston Motor (Front Wheel Assist) - Remove
AP600D and BG600D Asphalt Pavers Machine Systems Piston Motor (Front Wheel Assist) - Install
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Control Console
432E, 434E, 442E and 444E Backhoe Loaders Operator Controls
RM-300 Reclaimer Mixer Machine Systems Electrical System (Water and Additive Spray)
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Electrical System (Water and Additive Spray)
RM-300 Reclaimer Mixer Machine Systems Operator Controls (Water and Additive Spray System) - Modes of Operation
2290 Track Feller Buncher, 2390 Track Feller Buncher, 2391 Track Feller Buncher and 2491 Track Feller Buncher Machine Systems General Information
2290 Track Feller Buncher, 2390 Track Feller Buncher, 2391 Track Feller Buncher and 2491 Track Feller Buncher Machine Systems Piston Pump (Main Hydraulic)
2290 Track Feller Buncher, 2390 Track Feller Buncher, 2391 Track Feller Buncher and 2491 Track Feller Buncher Machine Systems Control Valve (Main)
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders Power Train Piston Motor (Hydrostatic) - Install
AccuGrade® GPS (CD700) Guidance to Dynamic Layered Lift Alignments