AP600D and BG600D Asphalt Pavers Machine Systems Caterpillar


Piston Motor (Front Wheel Assist) - Remove

Usage:

AP-600D TFM

Removal Procedure

Start By:

  1. Remove the front wheel. Refer to Disassembly and Assembly, "Wheel (Front Wheel Assist) - Remove and Install".

------ WARNING! ------

Personal injury can result from hydraulic oil pressure and hot oil.

Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide"for tools and supplies to collect and contain fluids in Caterpillar machines.

Dispose of all fluids according to local regulations.


Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.

  1. Drain the hydraulic oil from the hydraulic oil tank into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual for the correct procedure.


    Illustration 1g01529097

  2. Disconnect hose assemblies (2) from piston motor (1).


    Illustration 2g01529098

  3. Disconnect hose assembly (3).


    Illustration 3g01529100

  4. Remove bolts (4) from piston motor (1).


    Illustration 4g01529102

  5. Attach a suitable lifting device to piston motor (1). Remove bolts (5) and remove piston motor (1) from the machine. The weight of piston motor (1) is approximately 39 kg (86 lb).

Caterpillar Information System:

AP555E and BG555E Asphalt Pavers Machine Systems Piston Motor (Propel) - Assemble
AP555E and BG555E Asphalt Pavers Machine Systems Piston Motor (Propel) - Disassemble
432E, 434E, 442E and 444E Backhoe Loaders Specifications
793F Off-Highway Truck Power Train Modulating Valve (Transmission Clutch Engaging) - Disassemble
3512C Engine and 785D Off-Highway Truck/Tractors Diagnostic Trouble Codes
432E, 434E, 442E and 444E Backhoe Loaders Rated Load
AS4251C Asphalt Screed Shoe (End Gate) - Remove and Install
AS4251C Asphalt Screed Screed Frame (Extender) - Remove and Install
2008/05/19 A New Gasket is Available for Mounting of the Air Starting Motor {1451, 7555}
AP600D Asphalt Paver Propel System Piston Pump Neutral - Test and Adjust
422E and 428E Backhoe Loaders Swing Lock Pin Control
422E and 428E Backhoe Loaders Work Tool Flow Control - If Equipped
AP600D and BG600D Asphalt Pavers Machine Systems Piston Motor (Front Wheel Assist) - Install
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Control Console
432E, 434E, 442E and 444E Backhoe Loaders Operator Controls
RM-300 Reclaimer Mixer Machine Systems Electrical System (Water and Additive Spray)
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Electrical System (Water and Additive Spray)
RM-300 Reclaimer Mixer Machine Systems Operator Controls (Water and Additive Spray System) - Modes of Operation
2290 Track Feller Buncher, 2390 Track Feller Buncher, 2391 Track Feller Buncher and 2491 Track Feller Buncher Machine Systems General Information
2290 Track Feller Buncher, 2390 Track Feller Buncher, 2391 Track Feller Buncher and 2491 Track Feller Buncher Machine Systems Piston Pump (Main Hydraulic)
2290 Track Feller Buncher, 2390 Track Feller Buncher, 2391 Track Feller Buncher and 2491 Track Feller Buncher Machine Systems Control Valve (Main)
279C, 279C2, 289C, 289C2 and 299C Compact Track Loaders Power Train Piston Motor (Hydrostatic) - Install
AccuGrade® GPS (CD700) Guidance to Dynamic Layered Lift Alignments
2290 Track Feller Buncher, 2390 Track Feller Buncher, 2391 Track Feller Buncher and 2491 Track Feller Buncher Machine Systems Leveling System
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.