Rear Axle, Differential and Final Drive - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-7405     | 吊环螺栓     | 1     |
B     | 189-0863     | 钩环组件     | 2     |
C     | 138-7574     | 连杆支架     | 4     |
D     | 309-2793     | 负载平衡装置     | 1     |
E     | 155-0695     | 螺纹锁固定胶     | 1     |
- 利用工具 (B) 、工具 (C) 和工具 (D) 定位后桥、差速器和终传动 (7) 。 后桥、差速器和终传动 (7) 的重量大约为 4128 kg (9100 lb)。
Show/hide table
图 1 | g01528874 |
Show/hide table
图 2 | g01528819 |
- 将工具 (E) 涂抹到螺栓 (13) 上。 安装螺栓 (13) 。 将螺栓 (13) 上紧到 900 N·m (664 lb ft) 的扭矩。 在对面重新执行此步骤。
Show/hide table
图 3 | g01529072 |
Show/hide table
图 4 | g01529069 |
- 将工具 (E) 涂抹到螺栓 (14) 上。 安装螺栓 (14) 。 将螺栓 (14) 上紧到 900 N·m (664 lb ft) 的扭矩。 在对面重新执行此步骤。
- 将螺栓 (14) 上紧到 2000 ± 250 N·m (1475 ± 184 lb ft) 的扭矩。
Show/hide table
图 5 | g01529276 |
- 将螺栓 (13) 上紧到 2000 ± 250 N·m (1475 ± 184 lb ft) 的扭矩。
- 连接软管组件 (12) 。
Show/hide table
图 6 | g01529045 |
- 安装夹子 (11) 。
Show/hide table
图 7 | g01529036 |
- 连接软管组件 (10) 。 连接线束组件 (9) 。 连接软管组件 (8) 。
Show/hide table
图 8 | g01529009 |
- 拆下工具 (B) 、工具 (C) 和工具 (D) 。
- 安装带有 X 标记的两条螺栓 (8) 。 将两条螺栓 (6) 上紧到 900 ± 100 N·m (664 ± 74 lb ft) 的扭矩。
Show/hide table
图 9 | g01529019 |
- 将 O 型密封圈 (5) 安装到止推销 (4) 上。
Show/hide table
图 10 | g01561341 |
- 利用工具 (A) 安装止推销 (4) 。 卸下工具 (A) 。
Show/hide table
图 11 | g01561369 |
- 将销钉 (4) 推入后桥壳体,直到销钉 (4) 接触托架组件上的轴承盖为止。 测量销钉 (4) 端面与后桥壳体表面 (X) 间的距离。 将测量结果记为尺寸 (A) 并减去 0.050 到 0.025 mm (0.002 ± 0.001 in)。
- 安装几片垫片 (3) ,其厚度等于尺寸 (A) 。 安装盖 (2) 和螺栓 (1) 。
Show/hide table
图 12 | g01561334 |
- 安装后桥。 请参阅操作和保养手册, "变速箱和差速器用油 - 更换"。
End By:
- 安装万向节。 请参阅 拆解和装配, "万向节(输出) - 拆卸和安装"。
- 安装纵列传动箱。 请参阅 拆解和装配, "纵列传动箱和盖板 - 拆卸和安装"。
- 安装裂土器。 请参阅 拆解和装配, "裂土器 - 拆卸"。
Caterpillar Information System:
24M Motor Grader Power Train Rear Axle, Differential and Final Drive - Remove
795F AC and 795F AC XQ Off-Highway Truck Steering System Piston Pump (Hydraulic Fan)
AP600D Asphalt Paver Propel System Piston Pump Flow - Test
AP600D Asphalt Paver Propel System Hydraulic Oil Contamination - Test
3054C Engines for Caterpillar Built Machines Fuel Injection Pump Timing - Adjust
RM-300 Reclaimer Mixer Machine Systems Control Console
420E and 430E Backhoe Loaders Hydraulic and Steering System Hydraulic Pump - Test and Adjust
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Exhaust Temperature Is Too High
420E and 430E Backhoe Loaders Hydraulic and Steering System Bank Valve (Loader) - If Equipped
24M Motor Grader Power Train Final Drive - Assemble
24M Motor Grader Power Train Final Drive - Disassemble
420E and 430E Backhoe Loaders Hydraulic and Steering System Makeup and Relief Valve
422E and 428E Backhoe Loaders Work Tool Flow Control - If Equipped
422E and 428E Backhoe Loaders Swing Lock Pin Control
AP600D Asphalt Paver Propel System Piston Pump Neutral - Test and Adjust
2008/05/19 A New Gasket is Available for Mounting of the Air Starting Motor {1451, 7555}
AS4251C Asphalt Screed Screed Frame (Extender) - Remove and Install
AS4251C Asphalt Screed Shoe (End Gate) - Remove and Install
432E, 434E, 442E and 444E Backhoe Loaders Rated Load
3512C Engine and 785D Off-Highway Truck/Tractors Diagnostic Trouble Codes
793F Off-Highway Truck Power Train Modulating Valve (Transmission Clutch Engaging) - Disassemble
432E, 434E, 442E and 444E Backhoe Loaders Specifications
AP555E and BG555E Asphalt Pavers Machine Systems Piston Motor (Propel) - Disassemble
AP555E and BG555E Asphalt Pavers Machine Systems Piston Motor (Propel) - Assemble