Radiator Guard - Tilt
Tilting Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | FT-1115 | Vacuum Cap | 1 |
| 9S-8008 | Plug | 1 | |
| 3D-2824 | O-ring | 1 | |
| B | 138-7574 | Link Bracket | 2 |
| C | FT-1410 | Threaded Rod3/4 by 10 by 24 in. | 1 |
| 5P-5247 | Hydraulic Puller | 1 | |
| 2J-3506 | Full Nut | 2 | |
| D | 1U-9201 | Lever Puller Hoist | 1 |
| 1U-8221 | Lifting Sling | 2 | |
| 140-7742 | Sleeve | 2 | |
- Position the tracks. Pins (1) must be positioned, as shown.
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
 | |
| Illustration 1 | g01359353 |
- Remove the hood. Refer to Disassembly and Assembly, "Hood - Remove and Install".
- Remove the side guards. Refer to Disassembly and Assembly, "Side Guards - Remove and Install".
- Drain the coolant into a suitable container for proper storage or disposal. Refer to Operation and Maintenance Manual, "Coolant - Fill".
- Position a suitable container under hoses (2) and (3). Disconnect hoses (2) and (3) .
Show/hide table
 | |
| Illustration 2 | g01359355 |
- Attach Tooling (A) onto hydraulic tank (4). Attach an air supply hose onto Tooling (A). Apply 276 kPa (40 psi) to 414 kPa (60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Show/hide table
 | |
| Illustration 3 | g01359359 |
- Disconnect hose assembly (5) .
Show/hide table
 | |
| Illustration 4 | g01359361 |
- Disconnect hose assembly (6) .
Show/hide table
 | |
| Illustration 5 | g01359365 |
- Disconnect hose assembly (7) .
Show/hide table
 | |
| Illustration 6 | g01359367 |
- Disconnect hose assembly (8). Disconnect hose assembly (9). Disconnect hose assembly (10) .
Show/hide table
 | |
| Illustration 7 | g01359368 |
- Remove hose (11) .
Show/hide table
 | |
| Illustration 8 | g01359369 |
- Disconnect harness assembly (12). Remove bolt (13) .
Show/hide table
 | |
| Illustration 9 | g01359373 |
- Loosen clamps (14). Slide hose (15) toward the engine. Remove hose (16) .
Show/hide table
 | |
| Illustration 10 | g01359380 |
- Remove plate (17).
Show/hide table
 | |
| Illustration 11 | g01359384 |
- Attach Tooling (B) and a suitable lifting device onto radiator guard (18) .
Show/hide table
 | |
| Illustration 12 | g01359385 |
- Remove bolt (19). Remove pin (1). Use Tooling (C) in order to remove pin (1) .
Show/hide table
 | |
| Illustration 13 | g01359387 |
- Repeat Step 16 for the opposite side.
- Tilt radiator guard (18). Attach Tooling (D) .
Show/hide table
 | |
| Illustration 14 | g01359388 |
Caterpillar Information System:
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Plate Locations and Film Locations
AP655D and BG655D Asphalt Pavers Engine Oil and Filter - Change
AP655D and BG655D Asphalt Pavers Engine Oil Sample - Obtain
AP655D and BG655D Asphalt Pavers Engine Oil Level - Check
AP655D and BG655D Asphalt Pavers Engine Mounts - Inspect
D6K Track-Type Tractor Power Train Track Adjuster - Disassemble
773D Off-Highway Truck Power Train Electronic Control Module (Power Train) - Remove and Install
14L Motor Grader Machine Systems Seat - Remove and Install
Payload Control System (PCS) 2.X Payload Control System/PC Off-Board System
Payload Control System (PCS) 2.X Calibration
Payload Control System (PCS) 2.X Sensors
Procedure for Updating the Time Zone on CAESultra 3rd Party Radios{733T, 7490, 7604} Procedure for Updating the Time Zone on CAESultra 3rd Party Radios{733T, 7490, 7604}
587T PipelayerEngine Supplement Radiator Guard - Tilt Back
2007/03/12 Correction to the Parts Manual, Rocker Arm Gp {1123}
C4.4 (Mech) Industrial Engine Product Lifting
C4.4 (Mech) Industrial Engine Engine Oil Level - Check
C4.4 (Mech) Industrial Engine Engine Description
C4.4 and C6.6 Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
C4.4 (Mech) Industrial Engine Engine Operation
C4.4 (Mech) Industrial Engine Overhaul Considerations
C4.4 (Mech) Industrial Engine Engine Air Precleaner - Check/Clean
C4.4 (Mech) Industrial Engine Radiator - Clean
C4.4 (Mech) Industrial Engine Engine Air Cleaner Service Indicator - Inspect
C4.4 (Mech) Industrial Engine Engine Air Cleaner Element (Single Element) - Inspect/Replace