Engine Oil Filter Base - Assemble
组装步骤
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修发动机时，请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前，要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品，请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 检查 O 形密封圈。 更换磨损或损坏的 O 形密封圈。
- 安装螺塞 (23) 和 O 形密封圈 (24) 。 拧紧螺塞 (23) 至扭矩为 100 ± 15 N·m (74 ± 11 lb ft)。
Show/hide table
 | |
| 图 1 | g01325687 |
- 如果拆下了双头螺栓，则安装双头螺栓 (22) 。 拧紧双头螺栓 (22) 至扭矩为 68 ± 7 N·m (50 ± 5 lb ft)。
Show/hide table
 | |
| 图 2 | g01325685 |
- 将 O 形密封圈 (21) 、测试端口 (20) 和防尘盖 (19) 安装到机油滤清器底座 (9) 上。
Show/hide table
 | |
| 图 3 | g01325684 |
- 将挡圈 (18) 、间隔套 (17) 、弹簧 (16) 、阀座 (15) 和螺栓 (14) 安装到机油滤清器底座 (9) 上。
Show/hide table
 | |
| 图 4 | g01325682 |
Show/hide table
 |
弹簧压缩零件如果安装不当，会伤害人体。 为避免伤害，遵照出版的装配程序，并穿上保护装备。 |
- 将阀 (13) 、弹簧组件 (12) 、O 形密封圈 (11) 和螺塞 (10) 安装到机油滤清器座 (9) 上。 拧紧螺塞 (10) 至扭矩为 100 ± 15 N·m (74 ± 11 lb ft)。
Show/hide table
 | |
| 图 5 | g01325679 |
Show/hide table
|
弹簧压缩零件如果安装不当，会伤害人体。 为避免伤害，遵照出版的装配程序，并穿上保护装备。 |
- 将柱塞 (8) 、弹簧 (7) 、O 形密封圈 (6) 和螺塞 (5) 安装到机油滤清器座 (9) 上。 拧紧螺塞 (5) 至扭矩为 100 ± 15 N·m (74 ± 11 lb ft)。
Show/hide table
 | |
| 图 6 | g01325673 |
Show/hide table
|
弹簧压缩零件如果安装不当，会伤害人体。 为避免伤害，遵照出版的装配程序，并穿上保护装备。 |
- 将柱塞 (4) 、弹簧 (3) 、O 形密封圈 (2) 和螺塞 (1) 安装到机油滤清器座 (9) 上。 拧紧螺塞 (1) 至扭矩为 100 ± 15 N·m (74 ± 11 lb ft)。
End By: 安装发动机机油滤清器底座。 请参考 拆解和组装, "发动机机油滤清器底座 - 安装"。
Caterpillar Information System:
16M Motor Grader Engine Supplement Engine Oil Filter Base - Disassemble
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Systems Control Manifold and Solenoid (Work Tool Positioner) - If Equipped
777G Off-Highway Truck Power Train Spindle (Rear) - Install
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Water and Emulsion Lines
777G Off-Highway Truck Power Train Spindle (Rear) - Remove
D6K Track-Type Tractor Hydraulic System Cat Data Link
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D, 297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and 272D XHP Skid Steer Loaders Power Train Piston Pump (Hydrostatic) - Assemble
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D, 297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and 272D XHP Skid Steer Loaders Power Train Piston Pump (Hydrostatic) - Disassemble
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil Screen - Remove and Install
Procedure to Salvage the Slots for the Pin and Holes for the Reaction Dowel in Transmission Clutch Plates, Pistons, and Housings {3030, 3050, 3169, 3170, 3190} Procedure to Salvage the Slots for the Pin and Holes for the Reaction Dowel in Transmission Clutch Plates, Pistons, and Housings {3030, 3050, 3169, 3170, 3190}
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Power Train Torque Converter - Assemble
C175-16 Locomotive Engine Restriction of Air Inlet and Exhaust
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines Self-Diagnostics
14M Motor Grader Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
777D and 777E Off-Highway Truck Air System and Brakes Temperature Sensor (Torque Converter Oil)
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil Pan - Remove - C175-16
14M Motor Grader Engine Supplement Fuel Priming Pump and Water Separator - Remove and Install
C11 and C13 Engines Fan Drive
PL61 Pipelayer and D6K Track-Type Tractor MID 039 - CID 1933 - FMI 04
C13 and C15 On-highway Engines Coolant Contains Oil
735, 740 and 740 EJECTOR Articulated Trucks - Noise from the Power Train Is Sometimes Part of Normal Operation{3030, 3073, 3157, 3166} 735, 740 and 740 EJECTOR Articulated Trucks - Noise from the Power Train Is Sometimes Part of Normal Operation{3030, 3073, 3157, 3166}
777E, 777F and 777G Off-Highway Truck Electric Drive Pump (Prelubrication) - Remove and Install
2006/11/20 Software for Track Feller Bunchers Has Been Updated {1408, 7490, 7620}
14M Motor Grader Engine Supplement Refrigerant Compressor - Remove and Install