Electric Drive Pump (Prelubrication) - Remove and Install
- Turn the power disconnect switch to the OFF position.
- Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Engine Oil and Filter- Change".
Show/hide table
Illustration 1 g01325887 - Disconnect hose assembly (1). Disconnect hose assembly (2). Disconnect cable assembly (3).
Show/hide table
Illustration 2 g01325884 - Disconnect cable assembly (4). Remove bolts (6). Remove brackets (5).
- Use two people in order to remove electric drive pump (7). The weight of electric drive pump (7) is approximately
23 kg (50 lb) .
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use two people in order to install electric drive pump (7). The weight of the electric drive pump is approximately
23 kg (50 lb) . - Install brackets (5). Install bolts (6). Connect cable assembly (4).
Show/hide table
Illustration 4 g01325887 - Connect hose assembly (1). Connect hose assembly (2). Connect cable assembly (3).
- Fill the engine with engine oil to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil and Filter- Change".
- Turn the power disconnect switch to the ON position.
Show/hide table
Illustration 3 | g01325884 |
Caterpillar Information System:
735, 740 and 740 EJECTOR Articulated Trucks - Noise from the Power Train Is Sometimes Part of Normal Operation{3030, 3073, 3157, 3166} 735, 740 and 740 EJECTOR Articulated Trucks - Noise from the Power Train Is Sometimes Part of Normal Operation{3030, 3073, 3157, 3166}
C13 and C15 On-highway Engines Coolant Contains Oil
PL61 Pipelayer and D6K Track-Type Tractor MID 039 - CID 1933 - FMI 04
C11 and C13 Engines Fan Drive
14M Motor Grader Engine Supplement Fuel Priming Pump and Water Separator - Remove and Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil Pan - Remove - C175-16
777D and 777E Off-Highway Truck Air System and Brakes Temperature Sensor (Torque Converter Oil)
14M Motor Grader Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines Self-Diagnostics
16M Motor Grader Engine Supplement Engine Oil Filter Base - Assemble
16M Motor Grader Engine Supplement Engine Oil Filter Base - Disassemble
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Systems Control Manifold and Solenoid (Work Tool Positioner) - If Equipped
2006/11/20 Software for Track Feller Bunchers Has Been Updated {1408, 7490, 7620}
14M Motor Grader Engine Supplement Refrigerant Compressor - Remove and Install
PL61 Pipelayer and D6K Track-Type Tractor MID 039 - CID 2211 - FMI 03
3126B Engine for Caterpillar Built Machines Analog Sensor Supply Circuit - Test
777G Off-Highway Truck Power Train Transmission Hydraulic Control - Disassemble
C15 and C18 Petrolem Generator Set Engines Oil Contains Fuel
RM-300 Reclaimer Mixer Machine Systems Hydraulic Lines (Emulsion Pump)
777D and 777E Off-Highway Truck Air System and Brakes Operational Checks
777D and 777E Off-Highway Truck Air System and Brakes Brake Oil Overheating Troubleshooting
RM-300 Reclaimer Mixer Machine Systems Water and Emulsion Lines
777D and 777E Off-Highway Truck Air System and Brakes Relief Valve (Brake Oil Cooler) - Test and Adjust
450E Backhoe Loader Engine Starting with Starting Aid