- Load Haul Dump:
- R1700G (S/N: 8XZ1-UP)
Disassembly and Assembly, RENR4675, "R1700G Load Haul Dump Machine Systems", "Main Control Valve - Assemble". This module is part of Service Manual, RENR4656 Volume II.
The existing information in this module has been updated. Add the following supplemental information to the module that is referenced. Refer to "Assembly Procedure"
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Note: Lubricate all internal components with the lubricant that is being sealed.
Show/hide table
|
|
|
Illustration 1 | g01101185 |
Show/hide table
|
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
|
- Install the washer, bolt (47), shim pack (46), retainer (45), shim pack (44), spring (43), spring (42), retainer (41), shims (40), and spool (39) on lift valve spool (38) .
Show/hide table
|
|
|
Illustration 2 | g01074368 |
- Install tilt valve spool assembly (37) .
- Install lift valve spool assembly (38) .
Show/hide table
|
|
|
Illustration 3 | g01074366 |
- Install two housings (33) and the O-ring seals. Tighten four bolts (34) to a torque of 35 ± 3 N·m (26 ± 2 lb ft).
Show/hide table
|
|
|
Illustration 4 | g01074373 |
- Install two housings (36) and the O-ring seals. Tighten four bolts (35) to a torque of 35 ± 3 N·m (26 ± 2 lb ft).
Show/hide table
|
|
|
Illustration 5 | g01073948 |
Show/hide table
|
|
|
Illustration 6 | g01073947 |
Show/hide table
|
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
|
- Assemble makeup valve (27) .
- Install fitting (32) and O-ring seal (30) to makeup valve plug (31) .
- Install valve (28), spring (29) and makeup valve plug (31) in the valve body.
Show/hide table
|
|
|
Illustration 7 | g01073954 |
Show/hide table
|
|
|
Illustration 8 | g01073616 |
- Assemble check valve (23) .
- Install O-ring seals (24) to three load check valves (23) .
- Install three check valve (26), springs (25) and check valves (23) .
Show/hide table
|
|
|
Illustration 9 | g01073615 |
Show/hide table
|
|
|
Illustration 10 | g01073614 |
Show/hide table
|
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
|
- Assemble main relief valve (14) .
- Install O-ring seals (15), O-ring seal (16) to body (18) .
- Install O-ring seal (17) to cap (21) .
- Install valve (19), spring (20) and cap (21) to body (18) .
- Install main relief valve (14). Tighten main relief valve (14) to a torque of 110 ± 10 N·m (80 ± 7 lb ft).
Show/hide table
|
|
|
Illustration 11 | g01101184 |
Show/hide table
|
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
|
- Assemble O-ring seal (4), O-ring seal (5), locknut (7), retainer (8), O-ring seal (6), washer (13), spring (12), plate (11), valve (10), and valve body (9) to relief valve (2) .
Show/hide table
|
|
|
Illustration 12 | g01101183 |
Show/hide table
|
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
|
- Assemble O-ring seal (4), O-ring seal (5), locknut (7), retainer (8), O-ring seal (6), spring (12), plate (11), valve (10), and valve body (9) to relief valve (1) .
Show/hide table
|
|
|
Illustration 13 | g01073611 |
- Install tilt cylinder rod end relief valve (1) and tilt cylinder head end relief valve (2). Tighten the two relief valves to a torque of 65 ± 5 N·m (48 ± 4 lb ft).