Mixing Chamber - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-9201     | 操纵杆滚轮举倾机构     | 1     |
B     | 137-4370     | 均载梁     | 1     |
C     | FT-2977     | 防滑板     | 1     |
开始:
- 拆卸轮胎和轮辋(后)。 拆解和组装, "轮胎和轮缘(后)- 拆卸和安装"。
- 拆下油箱。 请参阅拆解和组装, "油箱(转子传动装置润滑)- 拆卸和安装"。
- 拆下转子传动轴。 请参阅拆解和组装, "转子传动轴 - 拆卸和安装"。
- 拆下两个液压油缸(转子提升)。 请参阅拆解和组装, "液压油缸(转子提升)- 拆卸和安装"。
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
Show/hide table
配备锁止阀的油缸即使在软管拆卸后也会长时间保持高压状态。 如果拆卸锁止阀或解体油缸之前没有释放所有压力,则可能会导致人身伤亡。 拆卸锁止阀或解体油缸之前确保释放所有压力。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修机器时,务必小心,确保用容器盛接流出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关可提供予卡特彼勒机器的工具及适合于盛装油液的容器,请参阅专门出版物, NENG2500, "卡特彼勒工具及车间用品指南"。 根据当地法规处置所有液体。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 拆下卡箍 (1) ,以将软管组件 (2) 移到一边。
Show/hide table
图 1 | g01276919 |
- 拆下螺栓 (6) 、垫圈 (5) 和螺母 (4) ,以将液压油缸 (7) 从混合室 (3) 上拆下。
Show/hide table
图 2 | g01276911 |
- 将软管组件 (8) 从前机罩门 (9) 上断开。
Show/hide table
图 3 | g01276444 |
- 将软管组件 (10) 从液压油缸 (11) 上断开。
Show/hide table
图 4 | g01276370 |
- 将开口销 (13) 、垫圈 (14) 、销 (15) 和混合室连杆 (12) 从混合室的两侧拆下。
Show/hide table
图 5 | g01276368 |
- 将适当的起吊设备连接到链盒。 提升链盒,然后将适当的垫块安装到链盒和混合室之间。 链盒和转子组件的重量约为 3950 kg (8700 lb)。
Show/hide table
图 6 | g01277973 |
- 将工具 (A) 和适当的吊索连接到混合室和转子轴上。
Show/hide table
图 7 | g01280860 |
注: 典型示例
- 拆下螺栓 (17) 和垫圈 (16) 。
Show/hide table
图 8 | g01277103 |
- 将工具 (B) 和适当的起吊设备连接到混合室 (3) 上。 混合室 (3) 和转子的重量约为 7940 kg (17500 lb)。
Show/hide table
图 9 | g01280858 |
- 将工具 (C) 安装到混合室下方,然后降低混合室。 将混合室组件 (3) 和转子从机器上拆下。
Caterpillar Information System:
How to Avoid Timestamp Problems with VIMS Advisor{7601} How to Avoid Timestamp Problems with VIMS Advisor{7601}
Starting and Charging Systems Key Start Switch Test Description
2006/06/05 An Optional Cover for the Sight Gauges On the Torque Converter Group Is Available {3101}
3508 EUI Engine for Off-Highway Truck/Tractors Temperature Switch
Starting and Charging Systems Key Breaker Test Description
Starting and Charging Systems Alternator Breaker Test Description
3508 EUI Engine for Off-Highway Truck/Tractors Magnetic Switch
3508 EUI Engine for Off-Highway Truck/Tractors Engine Speed Sensor
Starting and Charging Systems Batteries Test Description
3512C Engine for 785D Off-Highway Truck/Tractors Camshaft
Field Installation of the 266-2410 Backhoe Auxiliary Lines Gp (Kit) for 420E Backhoes with an Extendable Stick{5057} Field Installation of the 266-2410 Backhoe Auxiliary Lines Gp (Kit) for 420E Backhoes with an Extendable Stick{5057}
3176C Engines for Caterpillar Built Machines 5 Volt Engine Pressure Sensor Supply Circuit - Test
572R Series II Pipelayer Fast Fill Fuel Adapter
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Mixing Chamber - Install
572R Series II Pipelayer Fast Fill Fuel Adapter
Procedure to Fill Gear Pump with Oil Before Start-Up{5073} Procedure to Fill Gear Pump with Oil Before Start-Up{5073}
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 0713 - FMI 04
R1700G Load Haul Dump Power Train Differential and Bevel Gear (NoSPIN)
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 2683 - FMI 03
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 2683 - FMI 04
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 2683 - FMI 08
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 1326 - FMI 02
R1700G Load Haul Dump Power Train NoSPIN Differential
AccuGrade® GPS Using The CD550A Display (GPS/ATS/Sonic/Cross Slope) Light Bar - Configure