Service and Parking Brake
Show/hide table
 | |
| 图 1 | g01366900 |
Show/hide table
| 271-9321 行车和停车制动器总成的 技术规格 271-9322 行车和停车制动器总成的 技术规格 |
|||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 6 | 8T-4184 螺栓 | 拧紧螺栓至扭矩为 105 ± 20 mm (4 ± 0.8 in) |
| 组装前，将红色 Loctite 272 涂抹在螺栓的螺纹上。 | |||
| 2 | 4 | 2G-5681 弹簧 | 外径为 25.4 mm (1 in)。 |
| 试验力为 670 ± 33 N (150 ± 7.5 lb)。 |
|||
| 试验后的自由长度为 71.9 mm (2.83 in)。 |
|||
| 3 | 12 | 9W-7018 摩擦片 内 | 一块摩擦片的厚度为 5.08 ± 0.13 mm (0.20000 ± 0.005 in)。 |
| 一块摩擦片的最小可重用厚度为 4.42 mm (0.174 in) |
|||
| 组装前，用液压油润滑摩擦片。 | |||
| 4 | 13 | 7D-7504 外板 | 一块新外板的厚度为 2.4130 ± 0.0508 mm (0.095 ± 0.002 in) |
| 5 | 8 | 8T-0357 螺栓 | 拧紧螺栓至扭矩为 270 ± 40 N·m (200± 30 lb ft)。 |
| 组装前，将红色 Loctite 272 涂抹在螺栓的螺纹上。 | |||
| 6 | 1 | 4D-5642 垫片组 | 厚度为 2.89 ± 0.08 mm (0.114 ± 0.003 in)。 |
| 有关这些垫片安装的更多信息，请参阅您机器的拆解和组装手册。 | |||
| 7 | 12 | 8T-0643 螺栓 | 拧紧螺栓至扭矩为 60 ± 12 N·m (44 ± 9 lb ft)。 |
| 螺栓一次拧紧一圈，将壳体均匀拉下。 所有螺栓到底之后，以交叉顺序拧紧到最终扭矩。 有关这些螺栓安装的更多信息，请参阅您机器的拆解和组装。 |
|||
| 8 | 组装时，密封件以及与密封件接触的所有表面必须清洁干燥。 组装前，在金属密封圈上涂抹薄薄的一层机油。 | ||
| 用密封的润滑剂润滑密封件和孔。 | |||
Caterpillar Information System:
2006/01/30 Improved Filter Cover for the Transmission Filter {3067}
Payload Control System (PCS) 2.X MID 074 - CID 0168 - FMI 00
Payload Control System (PCS) 2.X Diagnostic Code List
Payload Control System (PCS) 2.X Using Service Display Mode to Determine Diagnostic Codes
Payload Control System (PCS) 2.X Payload Control System Troubleshooting without Diagnostic Codes
C15 and C18 Generator Set Engines Flywheel - Remove
24M Motor Grader Machine Systems Front Axle
24M Motor Grader Power Train Input Transfer Gears
587R Pipelayer Power Train Track Roller - Install
2006/01/30 A New Switch Is Used on Case Drain Filters {1408, 1435}
RM-300 Reclaimer Mixer Machine Systems Gear Pump (Rotor Transmission, PTO, and Oil Cooler) - Assemble
C4.4 (Mech) Industrial Engine Cooling System Coolant Level - Check
Payload Control System (PCS) 2.X MID 074 - CID 0168 - FMI 01
C15 and C18 Generator Set Engines Flywheel Housing - Remove and Install
Payload Control System (PCS) 2.X MID 074 - CID 0254 - FMI 12
Payload Control System (PCS) 2.X MID 074 - CID 0254 - FMI 13
Payload Control System (PCS) 2.X MID 074 - CID 0350 - FMI 01
Payload Control System (PCS) 2.X MID 074 - CID 0350 - FMI 02
Payload Control System (PCS) 2.X MID 074 - CID 0350 - FMI 13
2006/02/06 New Kits Are Available to Repair Cracks and Threads in Ductile Iron {0676, 0685}
Payload Control System (PCS) 2.X MID 074 - CID 0364 - FMI 01
C13, C15, and C18 Generator Set Engines Sensors and Electrical Connectors
583T Pipelayer Hydraulic System Solenoid Valve (Fan Bypass)
583T Pipelayer Machine Systems Counterweight Control Valve - Remove