Track Roller - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Description | Qty |
A | 504-9791 | Lift Gp (60Hz)(1) | 2 |
OR | |||
504-9793 | Lift Gp (50Hz)(2) | 2 | |
B | 183-4797 | Roller Lifting Fork As | 1 |
Show/hide table
(1) | High-Voltage (480V) Low-Voltage (240V) |
(2) | High-Voltage (400V) Low-Voltage (200V) |
- Use Tooling (B) and a suitable lifting device to position track roller (2) under the undercarriage. The weight of track roller (2) is approximately
95 kg (209 lb) . - Position caps (1) and bolts (3).
Note: Tighten the bolt on the abutment side first. “Tighten first” is stamped on cap (1).
- Tighten bolts (3) to a torque of
750 ± 70 N·m (550 ± 50 lb ft) . - Remove Tooling (B) from track roller (2).
Show/hide table
Illustration 2 g06280639 Show/hide tableIllustration 3 g06280638 - Use Tooling (A) to lower the side of the machine to the ground as shown in Illustration 2 and Illustration 3. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A).
- Tension the track. Refer to Operation and Maintenance, "Track - Check and Adjust".
Show/hide table
Illustration 1 | g01238826 |
Caterpillar Information System:
2006/01/30 A New Switch Is Used on Case Drain Filters {1408, 1435}
RM-300 Reclaimer Mixer Machine Systems Gear Pump (Rotor Transmission, PTO, and Oil Cooler) - Assemble
C4.4 (Mech) Industrial Engine Cooling System Coolant Level - Check
587R Pipelayer Power Train Final Drive
2007/05/21 Change to Stackup of the Discs in the Differential and Bevel Gear {3256, 3258}
24M Motor Grader Machine Systems Frame
24M Motor Grader Operator Controls
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Maintenance Interval Schedule
583T Pipelayer Machine Systems Steering Motor - Install
583T Pipelayer Machine Systems Steering Motor - Remove
2006/01/30 Correction to Disassembly and Assembly , "Differential and Bevel Gear (Center) - Assemble" {3256, 3258}
2006/01/30 Correction to Disassembly and Assembly , "Differential and Bevel Gear (Front and Rear) - Assemble" {3256, 3258}
24M Motor Grader Power Train Input Transfer Gears
24M Motor Grader Machine Systems Front Axle
C15 and C18 Generator Set Engines Flywheel - Remove
Payload Control System (PCS) 2.X Payload Control System Troubleshooting without Diagnostic Codes
Payload Control System (PCS) 2.X Using Service Display Mode to Determine Diagnostic Codes
Payload Control System (PCS) 2.X Diagnostic Code List
Payload Control System (PCS) 2.X MID 074 - CID 0168 - FMI 00
2006/01/30 Improved Filter Cover for the Transmission Filter {3067}
24M Motor Grader Braking and Hydraulic Fan System Service and Parking Brake
Payload Control System (PCS) 2.X MID 074 - CID 0168 - FMI 01
C15 and C18 Generator Set Engines Flywheel Housing - Remove and Install
Payload Control System (PCS) 2.X MID 074 - CID 0254 - FMI 12