Gear Pump (Rotor Transmission, PTO, and Oil Cooler) - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1857     | Retaining Ring Pliers     | 1     |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install lip seal (37) in end cover (27). Use Tooling (A) and install retaining ring (36) in end cover (27) .
Show/hide table
Illustration 1 | g01237306 |
- Install studs (35) in end cover (27) .
Show/hide table
Illustration 2 | g01237305 |
- Install backup ring (33) and seal (34) on end cover (27) .
- Install bushing (32) and O-ring seal (31) to housing (9) .
Show/hide table
Illustration 3 | g01237301 |
- Install backup ring (30) and seal (29) on end cover (27) .
Show/hide table
Illustration 4 | g01237300 |
- Install lip seal (28) in end cover (27) .
- Install end cover (27) on housing (9) and install bolts (26) .
Show/hide table
Illustration 5 | g01237299 |
- Install bushing (25), driven gear (24), and drive gear (23) in housing (9) .
Show/hide table
Illustration 6 | g01237298 |
- Install O-ring seal (22) on housing (9) .
- Install end cover (20) on housing (9) and install bolts (21) .
Show/hide table
Illustration 7 | g01237296 |
- Install coupler (19) .
Show/hide table
Illustration 8 | g01237295 |
- Install bushing (18), drive gear (17), and driven gear (16) in housing (6) .
Show/hide table
Illustration 9 | g01237294 |
- Install O-ring seal (15) on housing (6) .
- Install backup ring (14) and seal (13) on end cover (11) .
Show/hide table
Illustration 10 | g01237293 |
- Install end cover (11) on housing (6) and install bolts (10) .
Show/hide table
Illustration 11 | g01237292 |
- Install O-ring seal (12) on end cover (11) .
- Install housing (6) on housing (9) .
Show/hide table
Illustration 12 | g01237290 |
- Install bushing (8) and O-ring seal (7) on housing (6) .
- Install backup ring (5) and seal (4) on end cover (3) .
Show/hide table
Illustration 13 | g01237289 |
- Install end cover (3), bolts (2), and nuts (1) .
Show/hide table
Illustration 14 | g01237288 |
End By: Install the gear pump. Refer to Disassembly and Assembly, "Gear Pump (Rotor Transmission, PTO, and Oil Cooler) - Install".
Caterpillar Information System:
C4.4 (Mech) Industrial Engine Cooling System Coolant Level - Check
587R Pipelayer Power Train Final Drive
2007/05/21 Change to Stackup of the Discs in the Differential and Bevel Gear {3256, 3258}
24M Motor Grader Machine Systems Frame
24M Motor Grader Operator Controls
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Maintenance Interval Schedule
583T Pipelayer Machine Systems Steering Motor - Install
583T Pipelayer Machine Systems Steering Motor - Remove
2006/01/30 Correction to Disassembly and Assembly , "Differential and Bevel Gear (Center) - Assemble" {3256, 3258}
2006/01/30 Correction to Disassembly and Assembly , "Differential and Bevel Gear (Front and Rear) - Assemble" {3256, 3258}
2006/01/30 Correction to Disassembly and Assembly , "Differential and Bevel Gear (Center) - Assemble" {3256, 3258}
2006/01/30 Correction to Disassembly and Assembly , "Differential and Bevel Gear (Rear) - Assemble" {3256, 3258}
2006/01/30 A New Switch Is Used on Case Drain Filters {1408, 1435}
587R Pipelayer Power Train Track Roller - Install
24M Motor Grader Power Train Input Transfer Gears
24M Motor Grader Machine Systems Front Axle
C15 and C18 Generator Set Engines Flywheel - Remove
Payload Control System (PCS) 2.X Payload Control System Troubleshooting without Diagnostic Codes
Payload Control System (PCS) 2.X Using Service Display Mode to Determine Diagnostic Codes
Payload Control System (PCS) 2.X Diagnostic Code List
Payload Control System (PCS) 2.X MID 074 - CID 0168 - FMI 00
2006/01/30 Improved Filter Cover for the Transmission Filter {3067}
24M Motor Grader Braking and Hydraulic Fan System Service and Parking Brake
Payload Control System (PCS) 2.X MID 074 - CID 0168 - FMI 01