Drive Shaft (Rear) - Remove and Install
拆卸步骤
开始:
- 安装转向机架锁。 参考拆解和装配, "转向机架锁 - 拆卸和安装"。
Show/hide table
带载的传动系拧紧扭矩可造成人身伤害。 不等的车轮转速可产生传动系拧紧扭矩,从而使传动系部件在拆解中带载。 拆解前,务必释放传动系拧紧扭矩。 |
- 拆下六个螺栓 (2) 。 拆下护罩 (1) 。
Show/hide table
图 1 | g01210365 |
- 拆下两个螺栓 (3) 。 将歧管 (4) 移到一边。
- 拆下四个螺栓 (6) 、四个螺栓 (8) 以及四个螺栓 (9) 。 拆下护罩 (5) 和护罩 (7) 。
Show/hide table
图 2 | g01210370 |
- 拆下将传动轴 (11) 的每一端固定到输出分动器输出轭和后差速器上的八个螺栓 (10) 。
Show/hide table
图 3 | g01210373 |
- 拆下后传动轴 (11) 。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | Loctite 7649 Primer N     | -     |
B     | -     | Loctite 263     | -     |
Show/hide table
注意 |
---|
安装后传动轴时,必须将其安装在与后轴组件轭相同的相位上。 后传动轴必须安装于与中央和前部传动轴相同的相位上。 否则可能会发生严重的部件损坏。 确保校准所有接头总成、所有轭和所有润滑组件。 |
- 将后传动轴 (11) 放置在输出分动器输出轭和后差速器之间。
Show/hide table
图 4 | g01210373 |
注: 装配前,擦拭轴承盖和轭的安装面。 确保两个安装面均清洁。
- 安装八个螺栓 (10) 。 拧紧螺栓 (10) 至扭矩为 80 ± 15 N·m (60 ± 11 lb ft)。 利用图 5 中所示的数字顺序。
Show/hide table
图 5 | g00903158 |
- 按照数字顺序,每次一个,拆下螺栓 (10) 。 涂覆工具 (A) 后再将工具 (B) 涂覆到螺栓 (10) 的螺纹上。 安装螺栓 (10) 并拧紧至扭矩为 160 ± 15 N·m (120 ± 11 lb ft)。
- 对其余的螺栓 (10) 重复步骤 3。
- 安装护罩 (5) 和护罩 (7) 。 安装四个螺栓 (6) 、四个螺栓 (8) 以及四个螺栓 (9) 。
Show/hide table
图 6 | g01210370 |
- 定位歧管 (4) 。 安装两个螺栓 (3) 。
Show/hide table
图 7 | g01210365 |
- 定位护罩 (1) 。 安装六个螺栓 (2) 。
End By: 拆下转向机架锁。 参考 拆解和装配, "转向机架锁 - 拆卸和安装"。
Caterpillar Information System:
R1600G Load Haul Dump Power Train Drive Shaft (Center) - Remove and Install
R1600G Load Haul Dump Power Train Drive Shaft (Upper) - Remove and Install
R1300G Series II Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Remove
R1300G Series II Load Haul Dump Machine Systems Hydraulic Tank - Disassemble
R1300G Series II Load Haul Dump Machine Systems Hydraulic Tank - Remove
R1300G Series II Load Haul Dump Machine Systems System Pressure - Release
R1300G Series II Load Haul Dump Machine Systems Steering Cylinder - Install
R1300G Series II Load Haul Dump Machine Systems Steering Cylinder - Remove
R1300G Series II Load Haul Dump Power Train Transmission Planetary
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System Electronic Control Module (ECM)
CP-433E, CS-423E and CS-433E Vibratory Soil Compactors Lubricant Viscosities
3516B Off-Highway Trucks Ground Level Shutdown Switch
R1600G Load Haul Dump Power Train Drive Shaft (Front) and Drive Shaft Support Bearing - Remove
R1600G Load Haul Dump Power Train Drive Shaft (Front) and Drive Shaft Support Bearing - Install
R1600G Load Haul Dump Power Train Drive Shaft Support Bearing (Front) - Disassemble
R1600G Load Haul Dump Power Train Drive Shaft Support Bearing (Front) - Assemble
R1600G Load Haul Dump Power Train Axle Shaft - Remove
R1600G Load Haul Dump Power Train Axle Shaft - Install
Tier II Level Emissions Engine Repower for a 772B, 773B, and 775B Off-Highway Truck {1000} Tier II Level Emissions Engine Repower for a 772B, 773B, and 775B Off-Highway Truck {1000}
3516B Off-Highway Trucks Injector Solenoids
793D Off-Highway Truck Power Train Solenoid Valve - Test
793D Off-Highway Truck Power Train Transmission Hydraulic Control - Test
793D Off-Highway Truck Power Train Transmission Hydraulic Control (Pressure Pack) - Test and Adjust
AP-1000D and BG-260D Asphalt Pavers Machine Systems Piston Pump (Auxiliary) - Remove