Feeder Drive Shaft Group - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 9S-3263 | Thread Lock Compound | 1 |
- Use a suitable lifting device or a lift truck and position feeder drive shaft (12) in the machine, as shown. The weight of feeder drive shaft (12) is approximately
63 kg (140 lb) . - Install bearing (15) and bolts (14).
- Install bolts and shims (11) in bearing (10). Do not tighten the bolts at this time.
Show/hide table
Illustration 3 g01143129 - Measure the distance between the sprocket and the frame. This distance is Dimension (X). Dimension (X) must be
57.0 mm (2.24 inch) .Show/hide tableIllustration 4 g01147853 - Measure the distance between the tip of the sprocket teeth and the frame. This distance is Dimension (Y). Dimension (Y) should be approximately equal for the right and left sprockets. Tighten the bolts that hold bearing (10) to the frame.
Show/hide table
Illustration 5 g01143298 - Apply Tooling (A) to set screws (13) and install set screws (13).
Show/hide table
Illustration 6 g01143000 - Install tube assembly (6) in bearing.
- Install key (9) on the shaft.
- Install sprocket (8) on the shaft.
- Apply Tooling (A) to set screws (7) and install set screws (7).
Show/hide table
Illustration 7 g01142996 - Apply Tooling (A) to bolts (4) and install cap (5) and bolts (4).
Show/hide table
Illustration 8 g01142989 - Install master link (3), side plate (1), and cotter pins (2).
Show/hide table
Illustration 1 | g01143044 |
Show/hide table
Illustration 2 | g01143051 |
End By:
- Install the wheel (rear). Refer to Disassembly and Assembly, "Wheel (Rear) - Remove".
- Install the drag conveyor. Refer to Disassembly and Assembly, "Conveyor Drive (Drive Conveyor) - Remove".
Caterpillar Information System:
AP-1000D and BG-260D Asphalt Pavers Machine Systems Feeder Drive Shaft Group - Remove
AP-1000D and BG-260D Asphalt Pavers Daily Inspection
D7G Series 2 and D7G Series II Track-Type Tractors Lubricant Viscosities
C27 and C32 Generator Set Engines Poor Acceleration or Response
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Axles, Differential and Brakes Differential
Topcon® System Five Specifications
AP-1000D and BG-260D Asphalt Pavers Machine Systems Chain (Drag Conveyor) - Remove and Install
AP-1000D and BG-260D Asphalt Pavers Machine Systems Piston Motor (Drag Conveyor) - Install
793D Off-Highway Truck Power Train Pressure Sensor (Final Drive Oil)
793D Off-Highway Truck Hydraulic Fan System Piston Pump (Hydraulic Fan) Pressure - Test and Adjust
AccuGrade® Laser (CB420) MID 114 - CID 2259 - FMI 07
2005/09/12 New Procedures Improve the Service Life of the Check Valve {5051, 5067}
R1300G and R1300G Series II Load Haul Dumps Hydraulic System Accumulator (Ride Control)
R1300G and R1300G Series II Load Haul Dumps Hydraulic System Accumulator (Ride Control)
R1300G Series II Load Haul Dump Power Train Relief Valve (Transmission Hydraulic Control)
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Multiposition Switch Setup
AP-1000D and BG-260D Asphalt Pavers Propel System Front Wheel Assist
AP-1000D and BG-260D Asphalt Pavers Machine Systems Piston Motor (Auger Conveyor) - Remove
3412 Generator Set Engines Automatic Timing Advance Unit
3412 Generator Set Engines Automatic Timing Advance Unit
C15 Generator Set Engines Engine Will Not Crank
C175-16 and C175-20 Engines for Caterpillar Built Machines Cylinder Head - Remove
AP-1000D and BG-260D Asphalt Pavers Machine Systems Hydraulic Cylinder (Auger Hoist) - Remove and Install
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Safety Messages