Feeder Drive Shaft Group - Remove
Start By:
- Remove the drag conveyor. Refer to Disassembly and Assembly, "Conveyor Drive (Drag Conveyor) - Remove".
- Remove the wheel (rear). Refer to Disassembly and Assembly, "Wheel (Rear) - Remove".
- Remove cotter pins (1), side plate (2), and master link (3).
Show/hide table
Illustration 2 g01142996 - Remove bolts (4) and cap (5).
Show/hide table
Illustration 3 g01143000 - Loosen set screws (7).
- Remove sprocket (8).
- Remove key (9) from the shaft.
- Remove tube assembly (6) from the bearing.
Show/hide table
Illustration 4 g01143044 Show/hide tableIllustration 5 g01143051 - Use a suitable lifting device or a lift truck to provide support for feeder drive shaft (12), as shown. The weight of feeder drive shaft (12) is approximately
63 kg (140 lb) . - Remove bolts and shims (11) from bearing (10).
- Loosen set screws (13). Remove bolts (14) and bearing (15).
- Remove feeder drive shaft (12) from the machine.
Show/hide table
Illustration 1 | g01142989 |
Caterpillar Information System:
AP-1000D and BG-260D Asphalt Pavers Daily Inspection
D7G Series 2 and D7G Series II Track-Type Tractors Lubricant Viscosities
C27 and C32 Generator Set Engines Poor Acceleration or Response
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Axles, Differential and Brakes Differential
Topcon® System Five Specifications
AP-1000D and BG-260D Asphalt Pavers Machine Systems Chain (Drag Conveyor) - Remove and Install
AP-1000D and BG-260D Asphalt Pavers Machine Systems Piston Motor (Drag Conveyor) - Install
793D Off-Highway Truck Power Train Pressure Sensor (Final Drive Oil)
793D Off-Highway Truck Hydraulic Fan System Piston Pump (Hydraulic Fan) Pressure - Test and Adjust
AccuGrade® Laser (CB420) MID 114 - CID 2259 - FMI 07
2005/09/12 New Procedures Improve the Service Life of the Check Valve {5051, 5067}
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Machine Systems Lift Cylinder - Remove and Install
AP-1000D and BG-260D Asphalt Pavers Machine Systems Feeder Drive Shaft Group - Install
R1300G and R1300G Series II Load Haul Dumps Hydraulic System Accumulator (Ride Control)
R1300G and R1300G Series II Load Haul Dumps Hydraulic System Accumulator (Ride Control)
R1300G Series II Load Haul Dump Power Train Relief Valve (Transmission Hydraulic Control)
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Multiposition Switch Setup
AP-1000D and BG-260D Asphalt Pavers Propel System Front Wheel Assist
AP-1000D and BG-260D Asphalt Pavers Machine Systems Piston Motor (Auger Conveyor) - Remove
3412 Generator Set Engines Automatic Timing Advance Unit
3412 Generator Set Engines Automatic Timing Advance Unit
C15 Generator Set Engines Engine Will Not Crank
C175-16 and C175-20 Engines for Caterpillar Built Machines Cylinder Head - Remove
AP-1000D and BG-260D Asphalt Pavers Machine Systems Hydraulic Cylinder (Auger Hoist) - Remove and Install