834H Wheel Dozer and 836H Landfill Compactor Machine Systems Caterpillar


Seat - Install

Usage:

834H BTX

安装步骤




    图 1g01134336

  1. 需要两个人才能安装座椅支架 (45) 和 (46) 。 座椅支架 (45) 的重量约为 27 kg (60 lb)。 座椅支架 (46) 的重量约为 27 kg (60 lb)。



    图 2g01134272

  1. 需要两个人才能安装座椅悬架 (44) 。 座椅悬架 (44) 的重量约为 32 kg (70 lb)。



    图 3g01134255

  1. 安装螺栓 (43) 。



    图 4g01134254

  1. 连接线束组件 (42) 。



    图 5g01134253

  1. 由两人安装座椅 (41) 。 座椅 (41) 的重量约为 32 kg (70 lb)。



    图 6g01134252

  1. 安装螺栓 (40) 。



    图 7g01134251

  1. 安装座椅安全带 (38) 和螺栓 (39) 。



    图 8g01134212

  1. 定位电子液压支架 (37) 并安装轴 (36) 。



    图 9g01134210



    图 10g01134211

  1. 拧紧调整螺钉 (34) 和 (35) 。



    图 11g01134209

  1. 安装轴 (32) 和止动块 (31) 及 (33) 。



    图 12g01134208

  1. 拧紧调整螺钉 (29) 和 (30) 。



    图 13g01134207

  1. 安置面板 (25) 并安装螺栓 (26) 。 安装旋钮 (27) 并拧紧螺母 (28) 。



    图 14g01134206

  1. 将线束组件 (24) 连接至面板 (22) 。



    图 15g01134205

  1. 安置面板 (22) 并安装螺栓 (23) 。 安装旋钮 (21) 和缓冲块 (20) 。



    图 16g01134204

  1. 定位转向控制支架 (19) 并安装轴 (18) 。



    图 17g01134142



    图 18g01134144

  1. 拧紧调整螺钉 (16) 和 (17) 。



    图 19g01134141

  1. 安装轴 (14) 和止动块 (13) 及 (15) 。



    图 20g01134140

  1. 拧紧调整螺钉 (11) 和 (12) 。



    图 21g01134138

  1. 安置面板 (7) 并安装螺栓 (10) 。 安装旋钮 (8) 并拧紧螺母 (9) 。



    图 22g01134137

  1. 安置面板 (5) 并安装螺栓 (6) 。 安装旋钮 (3) 并拧紧螺母 (4) 。 安装旋钮 (2) 和缓冲块 (1) 。

End By: 分离转向机架锁。 请参阅 拆解和组装, "转向机架锁 - 分离和连接"。

Caterpillar Information System:

834H Wheel Dozer and 836H Landfill Compactor Machine Systems Seat - Remove
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Gear Pump (Implement, Pilot, Brake) - Install
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Gear Pump (Implement, Pilot, Brake) - Remove
AP1055D and BG2455D Asphalt Pavers Engine Supplement Exhaust (Muffler) - Remove and Install
988G Wheel Loader Power Train Output Transfer Gears - Disassemble
735 Articulated Truck Jacking/Blocking Locations
C11 and C15 Engines for Caterpillar Built Machines CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
C11 and C15 Engines for Caterpillar Built Machines CID 0275 FMI 03 Right Turbo Inlet Pressure open/short to +batt
C7 Engines for Caterpillar Built Machines Engine Oil Pressure - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning E12 - Recirculation Sensor (Short Circuit)
C7 Engines for Caterpillar Built Machines Turbocharger - Inspect
C7 Engines for Caterpillar Built Machines Fuel System Pressure - Test
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System Position Sensor for the Joystick Control (Operator Monitor) - Calibrate
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Steering Cylinder - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System Position Sensor for the Lift Linkage (Electronic Technician) - Calibrate
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System Position Sensor for the Lift Linkage (Operator Monitor) - Calibrate
2005/01/24 Correction to Disassembly and Assembly , "Assemble Brake, Steering and Pilot Pump" {4306}
R2900G Load Haul Dump Hydraulic System Main Hydraulic System
R2900G Load Haul Dump Hydraulic System Ride Control System
R2900G Load Haul Dump Steering System General Information
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning E13 - Fresh Air Sensor (Open Circuit)
C15 and C18 Engines for Caterpillar Built Machines Coolant Flow Switch Circuit - Test
C7 and C9 Engines for Caterpillar Built Machines Crank Without Inject Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Heating System Troubleshooting
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.