Output Transfer Gears - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-0520     | 冲头总成     | 1     |
B     | 0S-1591     | 螺栓     | 2     |
C     | 138-7573     | 连杆支架     | 4     |
D     | 8B-7548     | 推拉器工具总成     | 1     |
8B-7551 | 轴承拉拔器总成     | 1     | |
9S-9154 | 踏脚板     | 1     | |
E     | 8B-7554     | 轴承外圈拉拔器总成     | 1     |
8B-7548 | 推拉器工具总成     | 1     | |
F     | 8B-7554     | 轴承外圈拉拔器总成     | 1     |
8B-7548 | 推拉器工具总成     | 1     | |
8B-7549 | 拉拔器腿     | 2     | |
G     | 138-7575     | 连杆支架     | 2     |
H     | 8B-7548     | 推拉器工具总成     | 1     |
8B-7551 | 轴承拉拔器总成     | 1     | |
5P-4170 | 踏脚板     | 1     | |
8H-0684 | 棘轮扳手     | 1     |
开始:
- 将输出分动器从变速箱上分离。 请参阅拆解和组装, "变速箱与输入分动器和输出分动器 - 分离"。
- 拆下螺栓 (1) 和护圈 (2) 。
Show/hide table
图 1 | g01133945 |
- 拆下 O 型密封圈 (3) 和轭 (4) 。
Show/hide table
图 2 | g01133948 |
- 卸下螺栓 (5) 。 利用螺栓 (5) 松开轴承保持架 (6) 。 拆下轴承保持架 (6) 。
Show/hide table
图 3 | g01133953 |
Show/hide table
图 4 | g01133955 |
- 从轴承保持架 (6) 上卸下唇形密封 (7) 。 利用工具 (A) 从轴承保持架 (6) 上拆下轴承外圈 (8) 。 拆下 O 型密封圈 (9) 。
Show/hide table
图 5 | g01133973 |
Show/hide table
图 6 | g01133984 |
- 将输出分动器重新定位到适当的支座上。 输出分动器组件的重量约为 567 kg (1250 lb)。
Show/hide table
图 7 | g01133978 |
- 拆下螺栓 (10) 和护圈 (11) 。
Show/hide table
图 8 | g01134119 |
- 拆下 O 型密封圈 (12) 和轭 (13) 。
Show/hide table
图 9 | g01134125 |
- 从轴承保持架 (15) 上卸下螺栓 (14) 。
注: 记下螺栓 (14) 的位置。 螺栓 (14) 具有不同的长度。
Show/hide table
图 10 | g01134130 |
- 利用工具 (B) 松开轴承保持架 (15) 。
Show/hide table
图 11 | g01134133 |
- 将工具 (C) 和适当的起吊设备固定到轴承保持架 (15) 上。 轴承保持架 (15) 、传动轴 (16) 和齿轮 (18) 将作为一个整体拆卸。 轴承保持架 (15) 、传动轴 (16) 和齿轮 (18) 的重量约为 91 kg (200 lb)。 取下 O 形密封圈 (17) 。
Show/hide table
图 12 | g01134143 |
- 利用适当的压具将传动轴 (16) 从轴承保持架 (15) 和齿轮 (18) 上拆下。 传动轴 (16) 的重量大约为 25 kg (55 lb)。
Show/hide table
图 13 | g01153533 |
- 利用工具 (D) 将轴承 (19) 从传动轴 (16) 上拆下。
Show/hide table
图 14 | g01134164 |
- 将工具 (C) 和适当的起吊设备固定到轴承保持架 (15) 上。 从齿轮 (18) 上卸下轴承保持架 (15) 。 轴承罩 (15) 的重量大约为 41 kg (90 lb)。
Show/hide table
图 15 | g01134163 |
- 从轴承保持架 (15) 上卸下唇形密封 (20) 。
Show/hide table
图 16 | g01134170 |
- 将螺栓 (21) 和护圈 (22) 从轴承保持架 (15) 上拆下。
Show/hide table
图 17 | g01134192 |
- 利用适当的压具和工具 (A) 将两个轴承内圈 (23) 和一个轴承外圈 (24) 从轴承保持架 (15) 上拆下。
Show/hide table
图 18 | g01134223 |
Show/hide table
图 19 | g01134225 |
- 利用工具 (E) 将其余轴承外圈 (24) (未显示)从轴承保持架 (15) 上拆下。
Show/hide table
图 20 | g01134234 |
- 从齿轮 (18) 上拆下间隔套 (25) 。
Show/hide table
图 21 | g01134229 |
- 从轴承保持架 (27) 上卸下螺栓 (26) 。 利用螺栓 (26) 将轴承保持架 (27) 从盖 (28) 上拆下。
Show/hide table
图 22 | g01134232 |
Show/hide table
图 23 | g01134243 |
- 利用工具 (F) 将轴承外圈 (29) 从轴承保持架 (27) 上拆下。
Show/hide table
图 24 | g01134258 |
- 将垫片 (30) 从盖 (28) 上拆下。
Show/hide table
图 25 | g01134249 |
- 卸下螺母 (31) 和盖 (32) 。
Show/hide table
图 26 | g01134265 |
- 从轴承保持架组件 (35) 上卸下 O 型密封圈 (33) 。 拆下螺栓 (34) 。 将两条螺栓 (34) 装入孔 (X) 中并拆下轴承保持架组件 (35) 。
Show/hide table
图 27 | g01134269 |
- 利用工具 (F) 将轴承外圈 (37) 从轴承保持架 (35) 上拆下。 拆下 O 形密封圈 (36) 。
Show/hide table
图 28 | g01134301 |
- 卸下垫片 (38) 。
Show/hide table
图 29 | g01134299 |
- 将工具 (C) 和适当的起吊设备连接在盖 (28) 上。 盖 (28) 的重量约为 45 kg (100 lb)。 拆下螺栓 (39) ,然后拆下盖 (28) 。
Show/hide table
图 30 | g01134304 |
- 将传感器组件 (40) 从箱体组件 (41) 上拆下。
Show/hide table
图 31 | g01134308 |
- 由两人将齿轮 (43) 从箱体组件 (41) 上拆下。 齿轮 (43) 的重量大约为 39 kg (85 lb)。 由两人将齿轮 (42) 从箱体组件 (41) 上拆下。 齿轮 (42) 的重量大约为 30 kg (65 lb)。
Show/hide table
图 32 | g01134310 |
- 利用工具 (H) 将轴承内圈 (44) 从齿轮 (43) 上拆下。
Show/hide table
图 33 | g01134333 |
- 从齿轮 (42) 上卸下轴承内圈 (45) 。
Show/hide table
图 34 | g01134346 |
- 利用工具 (E) 将轴承外圈 (46) 和 (47) 从箱体组件 (41) 上拆下。
Show/hide table
图 35 | g01134324 |
Caterpillar Information System:
735 Articulated Truck Jacking/Blocking Locations
C11 and C15 Engines for Caterpillar Built Machines CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
C11 and C15 Engines for Caterpillar Built Machines CID 0275 FMI 03 Right Turbo Inlet Pressure open/short to +batt
C7 Engines for Caterpillar Built Machines Engine Oil Pressure - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning E12 - Recirculation Sensor (Short Circuit)
C7 Engines for Caterpillar Built Machines Turbocharger - Inspect
C7 Engines for Caterpillar Built Machines Fuel System Pressure - Test
735 and 740 Articulated Trucks Cab - Tilt
2005/02/07 Additional Information for the Operation and Maintenance Manual {7254, 7256}
259B3 Compact Track Loader, 247B3 and 257B Series 3 Multi Terrain Loaders and 216B Series 3, 226B3, 236B3, 242B Series 3 and 252B Series 3 Skid Steer Loaders Control Manifold (Quick Coupler)
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Wastegate - Test
267B, 277B and 287B Multi Terrain Loaders Machine Systems Piston Pump - If Equipped
AP1055D and BG2455D Asphalt Pavers Engine Supplement Exhaust (Muffler) - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Gear Pump (Implement, Pilot, Brake) - Remove
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Gear Pump (Implement, Pilot, Brake) - Install
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Seat - Remove
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Seat - Install
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System Position Sensor for the Joystick Control (Operator Monitor) - Calibrate
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Steering Cylinder - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System Position Sensor for the Lift Linkage (Electronic Technician) - Calibrate
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System Position Sensor for the Lift Linkage (Operator Monitor) - Calibrate
2005/01/24 Correction to Disassembly and Assembly , "Assemble Brake, Steering and Pilot Pump" {4306}
R2900G Load Haul Dump Hydraulic System Main Hydraulic System
R2900G Load Haul Dump Hydraulic System Ride Control System