Position Sensor (Left Brake Pedal) (Operator Monitor) - Calibrate
参考有关 操作员监视器的设置信息,请参阅正在维修的机器的测试和调整, "校准"。
采用子模式 29 校准变矩器踏板行程的参数。 位置传感器位于左侧制动器踏板下面。
叶轮离合器的变矩器踏板位置传感器的校准步骤
Show/hide table
机器突然移动,会造成人员伤亡。 机器突然移动,会对机上或机器附近的人员造成伤害。 在处理机器之前,执行以下程序,以防止可能的伤害。 |
- 将机器放在光滑、水平的表面上。
- 将变速箱方向控制开关移到空档位置。
- 将铲斗、铲刀或作业机具降至地面。
- 接合停车制动器。
- 轮子前后都塞上垫块。
- 安装转向机架锁。
- 关闭发动机。
注: 无需运行发动机即可执行校准过程。
- 将钥匙起动开关和断路开关转到 ON 位置。
- 机器上只留授权人员。 使未授权人员远离机器并在操作人员的清晰视野内。
Show/hide table
表 1 所需工具     零件号     说明     数量     4C-8195     控制维修工具     1    
- 利用 4C-8195 控制维修工具 通过 "MODE模式"开关进入变速箱校准模式(8)。 操作员监视器显示区应在释放 "MODE(模式)"开关后显示读数 "81"。
- 按下然后释放 "CLEAR(清除)"开关。 81 27 将显示在操作员监视器显示区上。
- 按下并松开 "SCROLL(滚动)"开关,直到 81 29 显示在操作员监视器显示区上。
- 按下并松开 "CLEAR(清除)"开关,开始校准。
注: 如果显示区显示读数 81 2904,进行步骤 16。
- 显示区显示读数 81 2902 时,接合停车制动器。
- 显示区显示读数 81 2903 时,将方向开关置于 NEUTRAL(空档)。
- 显示区显示读数 81 2904 时,完全踩下左制动器踏板然后再松开踏板。
- 按下然后释放 "CLEAR(清除)"开关。 如果显示区显示读数 81 29--,校准成功。 如果显示区显示读数 "29_EXX",校准不成功。 核对表 2 中的错误代码。
Show/hide table
表 2 变扭器踏板传感器校准故障错误代码     E002     存在正在进行的诊断     E009     ECM 已放弃     E103     校准值超出范围     E104     踏板范围过小     E105     踏板范围过大    
- 要退出子模式 29,采用 "SCROLL(滚动)"开关滚动至下一个子模式,或采用 "MODE(模式)"开关退出 Transmission Calibration Mode(变速箱校准模式。)
Caterpillar Information System:
R2900G Load Haul Dump Machine Systems Front Frame from Rear Frame - Separate
238-4569 Duct Gp-Air Custom Product Support Literature for Certain Load Haul Dump Machines{7320} 238-4569 Duct Gp-Air Custom Product Support Literature for Certain Load Haul Dump Machines{7320}
2004/08/02 Correction to Special Instruction, REHS2143, "Product Link PL-102C System Installation" {7602}
CB-434D and CB-434D Series XW Vibratory Compactors Engine Supplement Gear Motor (Fan Drive) - Install
446D Backhoe Loader Machine Systems Stabilizer Cylinder - Remove and Install
446D Backhoe Loader Machine Systems Floorplate - Remove and Install
PS-150C Pneumatic Compactor Propel System Relief Valve (Flushing Valve) - Test and Adjust - Machines with Optional Flow Divider
2004/12/01 Single Purpose Fluid Sampling Valves and Dual Purpose Fluid Sampling Valves Require Different Quick Connect Couplers {0645, 7542}
2004/07/26 A New Solenoid Control is Now Used {1265, 1276, 1408}
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Valve Mechanism
446D Backhoe Loader Machine Systems Piston and Vane Pump - Install
446D Backhoe Loader Machine Systems Piston and Vane Pump - Remove
2004/07/26 A New Improved Articulation Lock Pin and a New Hitch are Now Used {7050, 7051}
797B Off-Highway Truck Daily Inspection
C15 and C18 Engines for Caterpillar Built Machines Aftercooler - Test
2004/12/27 Portable Contamination Monitor Group Provides a Lower Cost Alternative to Particle Counting {0781, 0784, 0786, 1300, 5050}
C15 and C18 Engines for Caterpillar Built Machines Exhaust Temperature - Test
CB-214E, CB-224E and CB-225E Vibratory Compactors Machine Systems Steering Column - Remove and Install
CB-434D and CB-434D Series XW Vibratory Compactors Engine Supplement Engine - Remove
2004/07/19 Correction to Testing and Adjusting , "Operational Checks" {4251, 4278}
PS-150C Pneumatic Compactor Machine System Gear Pump (Steering)
PS-150C Pneumatic Compactor Machine System Metering Pump (Steering)
TK370, TK371, TK380 and TK381 Wheel Feller Bunchers Machine Systems Felling Head System - Industrial Tractor
446D Backhoe Loader Machine Systems Swing Frame - Remove