Oscillating Axle (Rear) to Output Transfer Gears - Connect
连接步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
B     | 138-7573     | 连杆支架     | 2     |
C     | 169-5464     | 快速硫化底漆     | 1     |
D     | 4C-9507     | 挡圈固定胶     | 1     |
E     | 155-0695     | 螺纹锁固胶     | 1     |
注: 安装前,确保所有安装面清洁。
- 安装 O 形密封圈 (6) 。
Show/hide table
图 1 | g01055636 |
- 将工具 (A) 和工具 (B) 固定到输出分动器 (1) 上。
Show/hide table
图 2 | g01055637 |
- 将适当的起吊设备连接到工具 (A) 和工具 (B) 上。
- 将输出分动器连接到差速器小齿轮壳体上。 输出分动器的重量约为 550 kg (1212 lb)。
Show/hide table
图 3 | g01055635 |
- 组装前,在螺栓螺纹上先涂敷工具 (C) ,再涂敷工具 (D) 。 安装将输出分动器固定在差速器小齿轮壳体上的 8 个螺栓 (5) 和垫圈。 拧紧螺栓 (5) 至扭矩为 475 ± 60 N·m (350 ± 45 lb ft)。
- 安装输出轴 (3) 。
Show/hide table
图 4 | g01055633 |
- 组装前,在螺栓螺纹上先涂敷工具 (C) ,再涂敷工具 (E) 。 安装螺栓 (4) 。 拧紧螺栓 (4) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。
- 将轭 (2) 安装在输出轴上。
Show/hide table
图 5 | g01055638 |
End By: 安装摆动轴和分动器。 请参阅 拆解和组装, "摆动轴(后)和输出分动器 - 安装"。
Caterpillar Information System:
AP-1000B and BG-260C Asphalt Pavers Conveyor Systems Cooling Manifold
R1300G Load Haul Dump Power Train Oscillating Axle (Rear) from Output Transfer Gears - Separate
M325D L MH and M325D MH Material Handlers Hydraulic System Travel Brake Valve
CP-323C and CS-323C Paving Compactors Engine Supplement Air Cleaner - Remove and Install
247B, 247B2, 257B and 257B2 Multi Terrain Loaders Power Train Bogie Wheel - Install
247B and 257B Multi Terrain Loaders Machine Systems General Information
248B and 268B Skid Steer Loaders Piston Motor (Hydrostatic) - Assemble
248B and 268B Skid Steer Loaders Piston Motor (Hydrostatic) - Disassemble
AP-1000B and BG-260C Asphalt Pavers Circuit Breakers - Reset
2004/04/12 A Guard for the Air Conditioner Belt and an Alternator Belt Guard Are Available {7174}
AP-1000B and BG-260C Asphalt Pavers Conveyor Systems Auger Conveyor
2004/03/08 A New Speed Sensor is Available {1907}
C13, C15, and C18 Generator Set Engines Engine Pressure Sensor Open or Short Circuit - Test
AP-655C and BG-2255C Asphalt Pavers Machine Systems Footshaft - Remove
AP555E and BG555E Asphalt Pavers Machine Systems Footshaft - Disassemble
AP555E and BG555E Asphalt Pavers Machine Systems Footshaft - Assemble
AP-655C and BG-2255C Asphalt Pavers Machine Systems Footshaft - Install
CB-334E and CB-335E Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Wheel Propel) - Test
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Power Train Limited Slip Differential - Disassemble - If Equipped
2004/03/15 Addition to Operation and Maintenance Manual , "Every 500 Service Hours or 3 Months" {4251}
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Power Train Limited Slip Differential - Assemble - If Equipped
2004/03/08 Improved Gasket for the Engine Oil Cooler {1378, 7555}
2004/03/01 Improved Gasket for the Engine Oil Cooler {1378, 7555}
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Power Train Oscillating Axle (Rear) and Trunnion Support - Remove