Fuel Injection Nozzles - Install
安装步骤
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 用清洁的发动机机油润滑座垫圈 (6) 。 将座垫圈安装在缸盖中。
注: 如果重新使用原来的座垫圈，喷油嘴的凸出量将不正确。
Show/hide table
 | |
| 图 1 | g00975210 |
- 将 O 形密封圈 (5) 安装到喷油嘴 (1) 上。 将喷油嘴安装到缸盖中。
注: 定位销 (X) 必须在卡箍 (4) 对面。
- 将卡箍 (4) 定位到喷油嘴上。 安装螺栓 (3) 。 拧紧螺栓至扭矩为 27 N·m (20 lb ft)。
- 将软管 (2) 安装在喷油嘴上。
End By: 安装喷油管路。 请参阅 拆解和组装, "燃油喷油管路 - 拆卸和安装"。
Caterpillar Information System:
C11 and C13 Engines for Caterpillar Built Machines Fuel System Pressure - Test
3054C Industrial Engine Fuel Injection Nozzles - Remove
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Piston Pump (Auxiliary) - Disassemble
2003/02/24 Serviceable Parts for the 166-0294 Work Tool Harness As {1408, 7000}
416D Backhoe Loader Fuel Tank Water and Sediment - Drain
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Piston Pump (Auxiliary) - Install
C15 and C18 Petroleum Generator Sets Fuel Conservation Practices
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
416D Backhoe Loader Tire Inflation - Check
3054C Industrial Engine Fuel Injection Lines - Remove and Install
247, 257, 267, 277 and 287 Multi Terrain Loaders Lower Machine Frame - Clean
RM-350B Road Reclaimer/Soil Stabilizer Maintenance Interval Schedule
AP-655C and BG-2255C Asphalt Pavers Drag Conveyor and Auger Conveyor Systems Location of Electrical Components (Auger Conveyor)
2004/05/03 New Midshaft Bearing Assemblies Now Used to Increase Service Life {3253}
PM-465 Cold Planer Additional Messages
789C Off-Highway Truck Machine Systems Summary of Revisions
AP-655C and BG-2255C Asphalt Pavers Machine Systems Hydraulic Schematic (Auxiliary Systems)
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Hood - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Hood - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Hood Tilt Actuator - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Belt Tensioner - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Alternator - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Electric Starting Motor - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install