Belt Tensioner - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 9U-6639     | Ratchet Wrench     | 1     |
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
- Open the hood.
- Use Tooling (A) to loosen belt (1) .
Show/hide table
Illustration 1 | g00956300 |
- Remove bolt (2) and remove belt tightener (3) .
Show/hide table
Illustration 2 | g00956350 |
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 9U-6639     | Ratchet Wrench     | 1     |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install belt tightener (3) and install bolt (2) .
Show/hide table
Illustration 3 | g00956350 |
- Use Tooling (A) to tighten belt (1) .
Show/hide table
Illustration 4 | g00956300 |
- Tighten the belt. Refer to Operation and Maintenance Manual, "Belts - Inspect/Adjust/Replace" for the correct procedure.
- Close the hood.
Caterpillar Information System:
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Hood Tilt Actuator - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Hood - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Hood - Remove
AP-655C and BG-2255C Asphalt Pavers Machine Systems Hydraulic Schematic (Auxiliary Systems)
789C Off-Highway Truck Machine Systems Summary of Revisions
PM-465 Cold Planer Additional Messages
2004/05/03 New Midshaft Bearing Assemblies Now Used to Increase Service Life {3253}
AP-655C and BG-2255C Asphalt Pavers Drag Conveyor and Auger Conveyor Systems Location of Electrical Components (Auger Conveyor)
3054C Industrial Engine Fuel Injection Nozzles - Install
C11 and C13 Engines for Caterpillar Built Machines Fuel System Pressure - Test
3054C Industrial Engine Fuel Injection Nozzles - Remove
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Piston Pump (Auxiliary) - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Alternator - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Electric Starting Motor - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Unit Injector Hydraulic Pump - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Unit Injector Hydraulic Pump - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Unit Injector - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Unit Injector - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Fuel Tank - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Fuel Tank - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Water Temperature Regulator - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Engine Supplement Water Pump - Remove