Engine Oil Filter Base - Remove and Install - Remote Mounted
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 185-3630 | 带式扳手组件 | 1 |
开始:
- 拆下发动机机油冷却器。
- 断开管组件 (3)。
- 断开管组件 ( 2)。
- 拆下四颗螺栓 (1)。
- 拆下螺栓 (4) 后拆下油滤清器底座 (5)。
Show/hide table
图 2 g02157868 - 拆下四条螺栓 (7) 后将歧管 (6) 从歧管 (8) 上分离。
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 拆下螺塞 (11)。 拆下弹簧 (10) 和柱塞 (9)。
Show/hide table
图 3 g02157869 注: 将滤清器壳体中的油排入适当的容器中,以便保存或处理。
- 断开管组件 (12)。
- 拆下螺栓 (13) 后拆下机油滤清器底座 (14)。
Show/hide table
图 4 g02157977 - 利用工具 (A) 拆下滤清器 (19)。
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 拆下螺塞 (18)、O 形圈 (17)、弹簧 (16) 和柱塞 (15)。
Show/hide table
图 1 | g02157867 |
- 按相反顺序安装机油滤清器底座。
- 拧紧螺塞 (18) 至扭矩为
100 ± 15 N·m (74 ± 11 lb ft) 。 - 利用工具 (A) 安装滤清器 (19)。 将滤清器 (19) 上紧到
100 ± 15 N·m (74 ± 11 lb ft) 的扭矩。
- 拧紧螺塞 (18) 至扭矩为
注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。
Caterpillar Information System:
794 AC Off-Highway Truck Windows - Clean
794 AC Off-Highway Truck Window Wiper - Inspect/Replace
794 AC Off-Highway Truck Engine Air Filter Primary Element - Clean/Replace
C175-16 Engine for 795F Series AC Off-Highway Trucks Fuel Injection Pump
3516C Petroleum Engines Engine Oil Cooler - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Nitrogen Oxide Sensor - Remove and Install
2013/07/08 New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202} 424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202}
374F Excavator Monitoring System
3500 Generator Sets Product Description
C15 and C18 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install - With Remote Mounted Oil Filter Base
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Power Take Off equipped
2013/06/18 Proper Pinout Locations on Certain Atlas Copco Industrial 3512C Engines {1408}
C4.4 Industrial Engine Safety Messages
3512C Oil Well Service Engines Starting the Engine
2013/06/20 Additional Support for the Bucket Circuit Tube Assembly is Available for Certain Excavators and Mobile Hydraulic Power Units {5057}
2013/06/26 A New Precooler Hose Is Now Used on Certain C18 Tier 4 Interim Industrial Engines {105P, 7554}
2013/09/16 Special Instructions Are Available for Retrofitting the Dynamic Gas Blending Kits on Certain 3512C Petroleum Engines {1250, 1280}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Reference Material
2013/06/26 Improved Ground Straps Have Been Added to the Diesel Exhaust Fluid Control Cabinet {1091, 1408}
2013/07/30 New Water Lines Are Available for the 355-4160 Throttle Gp on Certain CG137 Engines {1265, 1266}
Well Service Pumps Product Storage