Engine Oil Cooler - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 439-3938 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining and filling procedures.
Show/hide table
Illustration 1 g03395406 - Remove bolts (3).
- Attach Tooling (A) and a suitable lifting device to shell assembly (2). Shell Assembly weighs approximately
60 kg (133 lb) . - Remove bolts (1).
Show/hide table
Illustration 2 g03395620 - Remove bolts (4).
Show/hide table
Illustration 3 g03395806 - Remove bolts (6) and elbow (5).
- Remove engine oil cooler assembly (2).
- Install engine oil cooler assembly (2) in the reverse order of removal.
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Nitrogen Oxide Sensor - Remove and Install
2013/07/08 New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202} 424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202}
374F Excavator Monitoring System
3500 Generator Sets Product Description
C15 and C18 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install
C32 Generator Set Fuel Related Components in Cold Weather
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Manifold (DEF Heater) - Remove and Install
C175-16 Engine for 795F Series AC Off-Highway Trucks Fuel Injection Pump
794 AC Off-Highway Truck Engine Air Filter Primary Element - Clean/Replace
794 AC Off-Highway Truck Window Wiper - Inspect/Replace
794 AC Off-Highway Truck Windows - Clean
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install - Remote Mounted
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install - With Remote Mounted Oil Filter Base
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Power Take Off equipped
2013/06/18 Proper Pinout Locations on Certain Atlas Copco Industrial 3512C Engines {1408}
C4.4 Industrial Engine Safety Messages
3512C Oil Well Service Engines Starting the Engine
2013/06/20 Additional Support for the Bucket Circuit Tube Assembly is Available for Certain Excavators and Mobile Hydraulic Power Units {5057}
2013/06/26 A New Precooler Hose Is Now Used on Certain C18 Tier 4 Interim Industrial Engines {105P, 7554}