Valve Actuator (Variable) - Remove and Install
拆卸步骤
开始:
- 拆下气门机构盖。
注: 在卸下部件后不要拆解可变气门执行器。 可变气门执行器的任何拆解尝试都会使部件丧失保修。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 断开线束组件 (4) 。 断开线束组件 (1) 。
Show/hide table
图 1 | g01446246 |
- 拆下螺栓 (2) 。 卸下四个螺母 (3) 和两个螺母 (6) 。
- 卸下可变气门执行器 (5) 。
- 卸下支承 (11) 和螺柱 (10) 。
Show/hide table
图 2 | g01446248 |
- 卸下两个螺柱 (9) 和三个螺柱 (7) 。
- 卸下摇臂组件 (8) 。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将两个螺柱 (9) 安装在位置 6 和位置 7 处。 将螺柱 (9) 拧紧至至扭矩为 47 ± 9 N·m (35 ± 7 lb ft)。
Show/hide table
图 3 | g01446248 |
Show/hide table
图 4 | g01446408 |
- 将螺柱 (10) 安装在位置 2 处。 将双头螺栓 (10) 拧紧至扭矩为 65 ± 10 N·m (48 ± 7 lb ft)。 安装支承 (11) 。
- 安置摇臂组件 (8) 。 将三个螺柱 (7) 安装在位置 3、位置 4 和位置 5 处。 将螺柱 (7) 拧紧至至扭矩为 50 ± 5 N·m (37 ± 4 lb ft)。 再转动螺柱 (7) 45 ± 5 度。
- 安装可变气门执行器 (5) 。
Show/hide table
图 5 | g01446246 |
- 安装螺栓 (2) 。 安装四个螺母 (3) 。 安装两个螺母 (6) 。 请参照紧固顺序。
- 拧紧螺栓 (2) 至扭矩为 105 ± 20 N·m (77 ± 15 lb ft)。 拧紧螺母 (3) 至扭矩为 105 ± 20 N·m (77 ± 15 lb ft)。 拧紧螺母 (6) 至扭矩为 47 ± 9 N·m (35 ± 7 lb ft)。 按照数字顺序依次拧紧螺母和螺栓。
- 连接线束组件 (4) 。 将线束组件 (1) 连接到可变气门执行器 (5) 上。
- 先调整排气门上的间隙,然后调整可变气门执行器 (5) 上的压缩制动器。 有关压缩制动器间隙调整的更多资料,请参阅测试和调整, "压缩制动器间隙 - 调整"。 将防松螺母 (12) 拧紧至扭矩 15 ± 3 N·m (11 ± 2 lb ft)。
Show/hide table
图 6 | g01446444 |
End By: 安装气门机构盖。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Nitrogen Oxide Sensor - Remove and Install
2013/07/08 New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202} 424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202}
374F Excavator Monitoring System
3500 Generator Sets Product Description
C15 and C18 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install
C32 Generator Set Fuel Related Components in Cold Weather
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Manifold (DEF Heater) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electronic Control (Diesel Exhaust Fluid) - Remove and Install
3516C Petroleum Engines Engine Oil Cooler - Remove and Install
C175-16 Engine for 795F Series AC Off-Highway Trucks Fuel Injection Pump
794 AC Off-Highway Truck Engine Air Filter Primary Element - Clean/Replace
794 AC Off-Highway Truck Window Wiper - Inspect/Replace
794 AC Off-Highway Truck Windows - Clean
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install - Remote Mounted
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install - With Remote Mounted Oil Filter Base
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Power Take Off equipped
2013/06/18 Proper Pinout Locations on Certain Atlas Copco Industrial 3512C Engines {1408}
C4.4 Industrial Engine Safety Messages
3512C Oil Well Service Engines Starting the Engine
2013/06/20 Additional Support for the Bucket Circuit Tube Assembly is Available for Certain Excavators and Mobile Hydraulic Power Units {5057}