3500 Generator Sets Caterpillar


Product Description

Usage:

3516C JDH
Cat 3500C 发电机组由发动机、发电机和控制系统组成。

用途

此发电机用于产生电力。

发动机概述

3500C 发电机组 发动机是电子控制柴油发动机。 该发动机具有电子燃油喷油器。 该发动机可配备水套水后冷或者独立回路后冷。 该发动机具有 8 缸、12 缸和 16 缸发动机。

发动机的效率和发动机的性能取决于是否遵守正确操作和保养建议。 使用建议使用的燃油、润滑油和冷却液。 对空气滤清器、燃油系统、润滑系统 和冷却系统的保养应给予特别的注意。 关于保养事项的其他资料,请查阅操作和保养手册, "保养周期表"。

SR4 发电机描述

SR4B 无刷发电机可以用于以下负载:马达和灯的混合负载, SCR 控制的设备, 计算机中心, 通信装置 和 石油钻井应用。

可以利用发电机组设备产生主力电源或备用电源。

SR4B 发电机以三相全波的方式励磁和调压。 发电机设计为四极或六极。 机架尺寸决定发电机为六引线还是 12 引线。 发电机产生的电力可为 50 Hz 或 60 Hz 应用供电。

SR5 发电机描述

该 SR5 电刷发电机与下列负载一起使用:电机和灯光的混合负载, SCR 控制的设备, 计算机中心, 通信的安装 和 应用期间的石油。 励磁回路中免除电刷,减少了维护。 励磁回路中免除电刷,增大了可靠性。 电刷的免除,使得在可能存在的危险环境下的保护程度得以提高。

可以利用发电机组设备产生主力电源或备用电源。 发电机成套机组可用于陆基应用或船用。

SR5 发电机以三相全波的方式励磁和调压。 发电机有 4 个极。 发电机有 6 条导线配置。 发电机产生的电力可为 50 Hz 或 60 Hz 应用供电。

Caterpillar Information System:

C15 and C18 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install
C32 Generator Set Fuel Related Components in Cold Weather
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Manifold (DEF Heater) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electronic Control (Diesel Exhaust Fluid) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Filter - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Assemble
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove and Install
374F Excavator Monitoring System
424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202} 424-8895 C175 Crankshaft Lifting Tool{0599, 0629, 0632, 1202}
2013/07/08 New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
C15 and C18 Engines for Caterpillar Built Machines Nitrogen Oxide Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
3516C Petroleum Engines Engine Oil Cooler - Remove and Install
C175-16 Engine for 795F Series AC Off-Highway Trucks Fuel Injection Pump
794 AC Off-Highway Truck Engine Air Filter Primary Element - Clean/Replace
794 AC Off-Highway Truck Window Wiper - Inspect/Replace
794 AC Off-Highway Truck Windows - Clean
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install - Remote Mounted
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install - With Remote Mounted Oil Filter Base
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.