Cylinder Head
Show/hide table
| |
| 图 1 | g02648477 |
Show/hide table
| 304-0365 缸盖总成的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| - | 16
10 |
6I-4025 缸盖紧固件总成
106-5673 缸盖紧固件总成 |
以下螺栓的长度为 |
| 以下螺栓的长度为 |
|||
| 按照下列步骤拧紧缸盖的螺栓： | |||
| 按数字次序拧紧螺栓 1 到螺栓 26 至 |
|||
| 按数字次序拧紧螺栓 1 到螺栓 26 至 |
|||
| 再次按数字次序拧紧螺栓 1 到螺栓 26 至 |
|||
Show/hide table
| |
| 图 2 | g02648478 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| A | - | - | 新缸盖的厚度为 |
Show/hide table
| |
| 图 3 | g02648480 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| 凸轮轴衬套必须安装在正确的位置。 否则会造成发动机损坏。 | |||
| B | - | - | 衬套接合处的方向是高于水平 20 ± 5 度。 |
| C | - | - | 凸轮轴衬套的孔径为 |
Show/hide table
| |
| 图 4 | g02648482 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 7 | 216-5582 衬套 | 衬套的安装深度非常重要。 将衬套安装至以下深度： |
| 尺寸 (D) 为 |
|||
| 尺寸 (E) 为 |
|||
| 尺寸 (F) 为 |
|||
| 尺寸 (G) 为 |
|||
| 尺寸 (H) 为 |
|||
| 尺寸 (J) 为 |
|||
| 尺寸 (K) 为 |
Caterpillar Information System:
3516C Generator Set Engines Engine Speed/Timing Sensor
349F and 352F Excavators Machine System Specifications Solenoid Valve (System 16, 1-Way, 2-Pump)
CX28 On-Highway Transmission Transfer Gear Oil Level - Check
CG137-08 and CG137-12 Engines Exhaust Manifold - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Turbocharger
C13, C15, and C18 Tier 4 Final Engines Turbocharger
CG137-08 and CG137-12 Industrial Engines Lubrication System
C13, C15, and C18 Tier 4 Final Engines Turbocharger
C3.4B Engines for Caterpillar Built Machines Compression - Test
349E Excavator Machine System Specifications Auxiliary Hydraulic Lines - Coupler Lines
349E Excavator Machine System Specifications Auxiliary Hydraulic Lines - Coupler Lines
C13, C15, and C18 Tier 4 Final Engines Flywheel
G3600 A4 Engines Engine Speed Sensor
G3516H and G3520H Generator Set Engines Atmospheric Pressure Sensor
C175-16 Locomotive Engine Crankcase Pressure Sensor
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing
C175-16 Locomotive Engine Fuel Pressure Sensor
3512C and 3516C Marine Engines Air Starting Motor
CX28 On-Highway Transmission Transfer Gear Oil - Change
Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000} Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000}
2011/08/26 A New Hose Assembly Is Used for the Duplex Fuel Filters on Certain 3500 Engines {1261, 7554}
XQ125 Generator Set Electrical System
C27 Generator Set Product Storage
CX28 Military On-Highway Transmission Transfer Gear and Case - Check (Before Installation)