Fuel Filter Base - Remove and Install
Show/hide table
注意 |
---|
不要让脏物进入燃油系统。 彻底清洁将要拆开的燃油系统部件的周围区域。 在拆开的燃油系统部件上安放适当的盖。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 为了安装方便,在所有软管上作出识别标记。 塞住燃油滤清器底座上的所有软管和端口。 这将有助于防止液体泄漏和有助于防止污染物进入系统。
- 将燃油供应转到断开位置。
Show/hide table
图 1 g01302737 典型示例 - 松开软管卡箍 (4) 后断开软管 (5)。
- 如有必要,将燃油滤清器滤芯 (7) 从燃油滤清器底座 (1) 上拆下。 参阅操作和保养手册, "燃油系统滤清器 - 更换"。
- 拆下紧固件 (2),然后从安装支架上拆下燃油滤清器底座 (1)。
- 如有必要,将螺塞 (6) 和垫圈(未显示)从燃油滤清器底座 (1) 上拆下。 将管组件 (3) 和橡胶圈(未显示)从燃油滤清器底座 (1) 上拆下。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 如果发动机配备手动注油泵,该泵安装在燃油滤清器底座上。 燃油滤清器底座和手动注油泵的组件不可维修。
- 确保燃油滤清器底座清洁、无损坏。 如有必要,更换燃油滤清器底座。
Show/hide table
图 2 g01302737 典型示例 - 如有必要,将新的橡胶圈(未显示)安装到管组件 (3) 上。 将管组件 (3) 安装到燃油滤清器底座 (1) 上。 确保管组件的方位正确。 拧紧螺母至扭矩为
9 N·m (80 lb in) 。 - 将垫圈(未显示)安装到螺塞 (6) 上。 将螺塞 (6) 安装到燃油滤清器底座 (1) 上。 拧紧螺塞至扭矩为
23 N·m (17 lb ft) 。 - 将燃油滤清器底座 (1) 与安装支架对准。 安装紧固件 (2)。 拧紧紧固件至扭矩为
50 N·m (37 lb ft) 。 - 如有必要,将新的燃油滤清器滤芯 (7) 安装到燃油滤清器底座 (1) 上。 参阅操作和保养手册, "燃油系统滤清器 - 更换"。
- 连接软管 (5) 并拧紧软管卡箍 (4)。
注: 确保软管未接触任何其他发动机部件。
- 将燃油供应转到接通位置。
- 排出燃油系统中的空气。 请参阅操作和保养手册, "燃油系统 - 充油"。
Caterpillar Information System:
14L Motor Grader Machine Systems Circle Drive - Install
312D2 and 313D2 Excavators Machine Systems Storage Box and Covers (Cab) - Remove and Install
2008/01/01 Improved Routing of the Injector Wiring Harness {1290, 1408}
Reuse and Salvage for Camshafts {1210, 1210} Reuse and Salvage for Camshafts {1210, 1210}
G3520B Industrial Engines Prelubrication - Test
C32 Marine Auxiliary Engine Configuration Parameters
G3600 Engines Event Codes
G3600 Engines Diagnostic Trouble Codes
C11 and C13 Petroleum Engines Speed Sensor - Clean/Inspect
C32 Marine Auxiliary Engine Monitoring System
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Speed Control (Switch) - Test
3176C, 3406E and 3456 Industrial Engines Sensor Supply - Test
C4.4 Industrial Engine Maintenance Interval Schedule
3176C, 3406E and 3456 Industrial Engines Sensor Signal (Analog, Active) - Test
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C4.4 Industrial Engine Refill Capacities and Recommendations
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injector - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install