Turbocharger - Remove
拆卸步骤
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品，参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆卸空气滤清器。
- 拆下油管组件 (1) 。
Show/hide table
 | |
| 图 1 | g01116759 |
- 拆下排放管组件 (2) 。
- 拆下空气管 (3) 。 从空气管上拆下O 形密封圈。
Show/hide table
 | |
| 图 2 | g01116799 |
- 松开卡箍 (7) 。 将卡箍滑动到弯头连接器 (9) 上。
- 将适当的起吊设备连接到涡轮增压器 (8) 上。 3508B 涡轮增压器的重量约为 24 kg (53 lb)。
注: 3512B 涡轮增压器的重量约为 30 kg (66 lb)。 3516B 涡轮增压器的重量约为 47 kg (104 lb)。
- 拆下将涡轮增压器连接到排气歧管 (5) 上的螺栓 (4) 。 拆下涡轮增压器 (8) 。 拆下密封垫 (6) 。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
C9 Marine Generator Set Fuel System Secondary Filter - Replace
3412E Petroleum Engine General Information
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C15 and C18 Engines for Caterpillar Built Machines Fuel Filter Pressure Differential Switch
C-10 Petroleum Engine Exhaust Manifold
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Install
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove
C-10 Petroleum Engine Turbocharger
C15 and C18 Tier 4 Final Engines Cooling System - Check - Overheating
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove
C3.3 and C4.4 Generator Sets Fuel System Primary Filter/Water Separator - Drain
C15 and C18 Engines for Caterpillar Built Machines Belt Tensioner
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Install
C-10 Petroleum Engine Engine Oil Pan
3508B, 3512B and 3516B Generator Set Engines Turbocharger - Install
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Connector Locations
Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467} Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467}
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Diagnostic Capabilities
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines J1939 Bridge
3508C, 3512C and 3516C Marine Engines Water Temperature Regulators - Remove
3508C, 3512C and 3516C Marine Engines Water Temperature Regulators - Install
C-10 Petroleum Engine Piston Cooling Jet