Water Temperature Regulators - Remove
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 有关收集和盛接 Cat® 产品油液的合适工具和用品,请参阅专门出版物, PERJ1017, "代理商维修工具目录"。 按照本地法规和要求处置所有油液。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 排放冷却系统,直至冷却液的液位低于水温调节器壳体。
Show/hide table
图 1 g06123162 - 将软管组件 (1)和软管组件 (5)从水温调节器壳体 (6)上断开。
- 将管组件 (2) 从水温调节器壳体 (6) 上断开。 从管组件上拆下 O 形密封圈。
- 从水温调节器壳体断开管组件 (3)。
- 拆下螺栓 (4)。 卸下水温调节器壳体 (6)。
- 如有必要,拆下螺栓 (7),然后将出口弯头 (8) 从水温调节器壳体上拆下。 将密封垫从出口弯头上拆下。
Show/hide table
图 2 g06123164 - 拆下水温调节器 (12) 和密封垫 (9)。 从水温调节器壳体 (6) 上卸下唇形密封 (10)。
Show/hide table
图 3 g06123166 - 从水温调节器壳体上拆下通风阀 (12)。
Caterpillar Information System:
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines J1939 Bridge
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Diagnostic Capabilities
Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467} Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467}
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Connector Locations
3508B, 3512B and 3516B Generator Set Engines Turbocharger - Install
C-10 Petroleum Engine Engine Oil Pan
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove
C15 and C18 Engines for Caterpillar Built Machines Belt Tensioner
3508B, 3512B and 3516B Generator Set Engines Turbocharger - Remove
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
C9 Marine Generator Set Fuel System Secondary Filter - Replace
3508C, 3512C and 3516C Marine Engines Water Temperature Regulators - Install
C-10 Petroleum Engine Piston Cooling Jet
349F and 352F Excavators Swing Drive Oil - Change
PL1000E Communication ECM Electrical Connector - Inspect
C-10 Petroleum Engine Housing (Front)
PL1000E Communication ECM Wiring Harness (Open Circuit) - Test
PL1000E Communication ECM Wiring Harness (Short Circuit) - Test
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Electronic Control Module (ECM) - Flash Program
C15 and C18 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Electronic Control Module (ECM) - Configure
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Electronic Control Module (ECM) - Replace
3126B Petroleum Engine Can Not Reach Top Engine RPM