Water Temperature Regulators - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 221-8647 | 密封安装工具总成 | 1 |
B | 369-9450 | 润滑脂 | - |
C | 8S-1592 | 套筒 | 1 |
D | 1S-0258 | 塑料锤组件 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (C) 和 (D) 安装通风阀 (12)
Show/hide table
图 2 g06123164 - 将通风口组件 (13) 安装在水温调节器壳体 (6) 上。 安装密封垫 (12) 和 (11)。 安装螺栓 (10)。
- 使用工具 (A) 将唇形密封 (15) 安装到水温调节器壳体 (6) 中。
Show/hide table
注意 水温调节器 如果安装不正确,则会造成发动机过热。
- 安装水温调节器 (14)。
Show/hide table
图 3 g06123162 - 定位水温调节器壳体 (6),然后安装螺栓 (4)。
- 定位密封垫和出口弯头 (8) 并安装螺栓 (7)。
- 安装管组件 (3)。
- 连接软管组件 (1) 和 (5)。
- 将 O 形密封圈安装在管组件 (2) 上。 使用工具 (B) 润滑 O 形密封圈。 安装管组件 (2)。
- 加注冷却液到正确的液位。 参考操作和保养手册, 冷却系统冷却液 - 更换以了解正确的步骤。
Show/hide table
图 1 | g06123166 |
Caterpillar Information System:
3508C, 3512C and 3516C Marine Engines Water Temperature Regulators - Remove
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines J1939 Bridge
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Diagnostic Capabilities
Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467} Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467}
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Connector Locations
3508B, 3512B and 3516B Generator Set Engines Turbocharger - Install
C-10 Petroleum Engine Engine Oil Pan
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove
C15 and C18 Engines for Caterpillar Built Machines Belt Tensioner
3508B, 3512B and 3516B Generator Set Engines Turbocharger - Remove
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
C-10 Petroleum Engine Piston Cooling Jet
349F and 352F Excavators Swing Drive Oil - Change
PL1000E Communication ECM Electrical Connector - Inspect
C-10 Petroleum Engine Housing (Front)
PL1000E Communication ECM Wiring Harness (Open Circuit) - Test
PL1000E Communication ECM Wiring Harness (Short Circuit) - Test
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Electronic Control Module (ECM) - Flash Program
C15 and C18 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Electronic Control Module (ECM) - Configure
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Electronic Control Module (ECM) - Replace
3126B Petroleum Engine Can Not Reach Top Engine RPM
3412E Petroleum Engine Electronic Unit Injector - Test