Housing (Front)
Show/hide table
 | |
| Illustration 1 | g01117183 |
Front view of front housing | |
(1) Front housing
The rear face of the housing and the front face on the block must be free of the following items during assembly: oil, water, dirt, assembly compounds and any other contaminants.
(2) Bolt
Tighten these nineteen bolts to the standard torque.
(3) Bolt
Tighten this one bolt to the standard torque.
(4) Bolt
- Tighten these thirteen bolts to the following torque. ... 35 ± 8 N·m (26 ± 6 lb ft)
(5) Crankshaft seal
Tighten the nuts for the crankshaft seal in the numerical sequence that is shown in Illustration 2.
Show/hide table
 | |
| Illustration 2 | g01117234 |
Tightening sequence | |
Apply 8T-9022 Silicone Gasket in order to fill the space at the joint of the following items: cylinder block, front housing and oil pan.
Caterpillar Information System:
PL1000E Communication ECM Electrical Connector - Inspect
349F and 352F Excavators Swing Drive Oil - Change
C-10 Petroleum Engine Piston Cooling Jet
3508C, 3512C and 3516C Marine Engines Water Temperature Regulators - Install
3508C, 3512C and 3516C Marine Engines Water Temperature Regulators - Remove
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines J1939 Bridge
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Diagnostic Capabilities
Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467} Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467}
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Connector Locations
3508B, 3512B and 3516B Generator Set Engines Turbocharger - Install
C-10 Petroleum Engine Engine Oil Pan
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Install
PL1000E Communication ECM Wiring Harness (Open Circuit) - Test
PL1000E Communication ECM Wiring Harness (Short Circuit) - Test
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Electronic Control Module (ECM) - Flash Program
C15 and C18 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Electronic Control Module (ECM) - Configure
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Electronic Control Module (ECM) - Replace
3126B Petroleum Engine Can Not Reach Top Engine RPM
3412E Petroleum Engine Electronic Unit Injector - Test
3412E Petroleum Engine Electronic Unit Injector - Adjust
C-10 Petroleum Engine General Information
3500 Engines Turbocharger - Assemble - Type 2
3500 Engines Turbocharger - Disassemble - Type 2