Pistons and Connecting Rods - Remove
Show/hide table
| 需要的工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件名称 | 数量 |
| A | 9S-9082 | 发动机盘车工具 | 1 |
开始:
- 拆卸缸盖。 请参阅拆解和组装, "缸盖 - 拆卸"。
- 拆卸发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
- 拆卸活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 用工具 (A)旋转曲轴，直到活塞处于底部中央位置。
- 从缸套内表面顶部开始清除积炭凸起。
- 检查连杆和连杆盖上的标记是否正确。 连杆和连杆盖对侧面的编号应该有磨损。 该编号必须与气缸号一致。 如有必要，标记连杆和连杆盖。
注: 不要压印连杆组件。 在连杆组件上压印或冲孔会导致连杆断裂。
- 拆下螺栓 (1)和连杆轴承盖 (2)。
Show/hide table
图 2 g00998390 - 从缸套中卸下活塞 (3)和连杆。
Show/hide table
| |
| 图 1 | g00998389 |
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Fuel Filter Pressure Differential Switch
C-10 Petroleum Engine Exhaust Manifold
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Install
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove
C-10 Petroleum Engine Turbocharger
C15 and C18 Tier 4 Final Engines Cooling System - Check - Overheating
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove
C3.3 and C4.4 Generator Sets Fuel System Primary Filter/Water Separator - Drain
C-10 Petroleum Engine Valve Mechanism Cover
C15 and C18 Engines for Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
3412E Petroleum Engine General Information
C9 Marine Generator Set Fuel System Secondary Filter - Replace
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3508B, 3512B and 3516B Generator Set Engines Turbocharger - Remove
C15 and C18 Engines for Caterpillar Built Machines Belt Tensioner
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Install
C-10 Petroleum Engine Engine Oil Pan
3508B, 3512B and 3516B Generator Set Engines Turbocharger - Install
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Connector Locations
Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467} Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467}
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Diagnostic Capabilities