776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Caterpillar

Cover (Cab Front) - Remove and Install

Usage:

776D AFS

拆卸步骤

Show/hide table




图 1	g00648252

拆下将盖 (2) 固定到驾驶室上的 14 个螺栓 (1) 和硬垫圈。
拆下罩盖 (2)。盖的重量约为 15 kg (32 lb)。

安装步骤

注: 检查所有部件是否磨损或损坏。如有必要，请更换部件。利用不起毛的抹布擦拭所有部件。

Show/hide table




图 2	g00648252

将盖 (2) 放置到驾驶室上，如图所示。
安装将盖 (2) 固定到驾驶室上的 14 个螺栓 (1) 和硬垫圈。

Caterpillar Information System:

3114, 3116, and 3126 Engines Fuel System - Prime

CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Blade Valve and Mounting

3034 Engine for Caterpillar Built Machines Camshaft - Install

776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Assemble

776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Disassemble

2000/04/24 Rework for Certain Rear Lamp Housing Groups {1429}

24H Motor Grader Plate Locations and Film Locations

834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Electronic Technician) - Calibrate

834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate

776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Transmission and Transfer Gears - Separate

776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Assemble

776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Disassemble

Installation Procedure for Motorized Flow Control{5051} Installation Procedure for Motorized Flow Control{5051}

24H Motor Grader Battery Disconnect Switch

776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Rear) - Remove and Install

834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate

834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate

834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Electronic Technician) - Calibrate

797 Off-Highway Truck Power Train Relief Valve (Rear Axle Motor Unloader) - Disassemble

2000/04/17 The Torque For The Nuts On The Injector Wiring Harness Has Been Increased {1290}

24H Motor Grader Engine Start Switch

24H Motor Grader Drawbar Ball and Socket End Play - Check/Adjust

120H and 135H Motor Graders Circle Drive Pinion Teeth - Lubricate

3034 Engine for Caterpillar Built Machines Piston Cooling Jets - Remove and Install